588931
4
Zoom out
Zoom in
Previous page
1/38
Next page
To save energy, the HAC5 turns off automatically at night, meaning the display turns off at
12 p.m. and only lights up again after pressing any button.
All functions active at the time of shut-off keep going internally despite the display turned
down.
2. Operational Setup
2.1 Attaching the HAC5 to the wrist band and the handlebar bracket
To take the HAC5 out of the wrist band or the handlebar holder, turn it 90° to the left, then remove.
To insert into the wrist band or handlebar bracket, insert at a 90° angle to the left, then turn to right
until it engages.
2.2 Inserting the batteries
Inserting the battery into the HAC5:
The HAC5 is delivered with battery inserted. Just press any button to start.
(As the HAC5 uses a high tech display with Dot-Matrix, the battery consumption is – like in many other
high tech devices – more extensive than in our other CicloSport computers.
Therefore two extra batteries are added).
Inserting the battery into transmitter belt, speed- and cadence transmitter:
Open the battery cap with the aid of a coin (turn to left). Insert battery type CR2032 with the plus
pole facing up and close the cap again.
2.3 Setup / Initialization
Because of the new digital transmission technique, all transmitters have to be initialized prior to first
use. We therefore recommend that you first conduct all necessary initializations (and, if required,
enter all required data) before attaching the parts to the bike. In chapter 5 you will find a step-by-step
setup as well for the initializations as for setup of time and date.
2.4 Installing
Installing the handlebar bracket:
The handlebar mounting can also be installed on a stem. To do this the top section
of the handlebar mounting must be removed from the bottom section. To make
it easier to remove the top section carefully push the sides of the bottom section
upwards slightly.
Then turn both parts through 9 and assemble them again until the snap-on
mounting engages.
Remove the backing foil from the underside of the handlebar mounting, place the
handlebar mounting in the required position on the handlebar (or on the stem) and
press it down slightly. Secure it with the O ring or with the cable ties.
• Installing the speed transmitter:
Attach the speed transmitter at the fork or the rear construction with the aid of the cable ties (the
printed side of the transmitter with the marking must point to the spokes).
Mount the magnet to a spoke directly opposite the marking on the transmitter.
Do not over tighten the fixing screw on the magnet. Adjust transmitter in such a way that the
distance between transmitter and magnet does not exceed 3 millimetres.
• Installing the cadence transmitter:
Attach the cadence transmitter to a strut opposite the pedal crank with the aid of the cable ties
(the printed side of the transmitter with the marking must point to the crank).
Mount the magnet on the pedal crank directly opposite the transmitter with the help of the cable
tie, so that the magnet points exactly to the marking on the transmitter. Adjust transmitter in such
a way that the distance between transmitter and magnet does not exceed 3 millimetres.
4
Inserting the batteries
Setup / Initialization
Installing
Attaching the HAC5
to the wrist band and
the handlebar bracket
Attention!
Mark
handlebar
bracket
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ciclo HAC 5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ciclo HAC 5 in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ciclo HAC 5

Ciclo HAC 5 Additional guide - English - 4 pages

Ciclo HAC 5 Additional guide - German - 4 pages

Ciclo HAC 5 Quick start guide - German - 2 pages

Ciclo HAC 5 User Manual - German - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info