588918
4
Zoom out
Zoom in
Previous page
1/16
Next page
41
If the CM 628i fails to display any heart rate, it probably
means that there is no contact between the skin and the
electrodes. Moistening the electrodes and the underlying
skin often helps. Best results are obtained if electrode gel
is used (available from pharmacies).
3 .FUNCTIONALITY OF THE CM 628i
By means of the respective transmitter identification, the
CM 628i can automatically identify on which bike it is
being used.
For this, it is necessary that it is seated on the handlebar
bracket and only in this way is the built-in movement
sensor activated, which then initiates the transmitter
search with the first registered movement of the bike.
During the transmitter search a zero flashes in the upper
display and, if a transmitter is found, the flashing stops.
A non-flashing zero in the upper display means that a
transmitter has been found, however, it is not transmitting
any speed signal at this time i.e. the wheel is at a stand-
still.
The speed transmitter is activated with the first wheel
rotation and the cadence transmitter through the first pedal
rotation.
The transmitter search in the CM 628i can also be started
manually (if the CM 628i is located on the handlebar
bracket), this is done by pressing both buttons simultane-
ously for a short period.
The manual transmitter search functions only if no trans-
mitter has yet been found (' – ' in the upper display).
If a transmitter has already been found, briefly pressing
both buttons simultaneously changes between Bike 1 and
Bike 2.
Only when a speed transmitter has been found (and if the
cadence is switched on – setting adjustment mode 'C on'),
is the relevant cadence also searched for automatically.
If no cadence transmitter is mounted, this function should
be switched off in the setting adjustment mode, since the
cadence transmitter is normally searched for indefinitely
(and this search will drain the battery quicker).
After this the heart rate transmitter is searched (only when
the heart rate is switched on – setting adjustment mode 'H
on').
If heart rate measuring should be started without CM 628i
being on the handlebar bracket, press both buttons short
when lower display shows 'H –'.
magnet. Turn the
transmitter so that
the separation
distance between
transmitter and
magnet is not more
than 3 mm. To
check for correct
installation, rotate
wheel a few times and check whether the computer re-
ceives a signal.
2.3 Installing the optional cadence transmitter
Attach cadence transmitter to a strut opposite the pedal
crank with the aid of the O-ring. Hang the O-ring on one
side of the transmitter, wrap around the strut and hook
back on the opposite side.
Mount the magnets on the pedal crank directly opposite
the transmitter with the aid of the cable tie (do not fully
tighten at this time), so that the magnet points exactly to
the marker on the transmitter. Turn the transmitter so that
the separation distance between transmitter and magnet is
not more than 3 mm. To check for correct installation,
rotate the pedal a few times and check whether the
computer receives a signal. Then tighten up cable ties.
2.4 Putting on the heart rate transmission belt
The transmitter belt is hung in
the elastic chest belt and
fastened around the upper
body. The transmitter (the
plastic part with the company
logo) should lie over the
middle of the upper stomach,
immediately below the breast-
bone, so that the logo on the
transmitter is legible (viewed from the front) (see illustra-
tion). The electrodes in the belt, to the right and left of the
transmitter, must be in contact with the skin.
Pull the belt tight so that it cannot slip and constant con-
tact with the body is guaranteed during movement.
max. 3 mm
Electrodes
Transmitter
40
02 CM 628i engl 34-65 27.09.2005 8:40 Uhr Seite 8
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ciclo CM 628i Master at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ciclo CM 628i Master in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ciclo CM 628i Master

Ciclo CM 628i Master User Manual - German - 17 pages

Ciclo CM 628i Master User Manual - Danish - 17 pages

Ciclo CM 628i Master User Manual - French - 16 pages

Ciclo CM 628i Master User Manual - Italian - 16 pages

Ciclo CM 628i Master User Manual - Spanish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info