793032

Christopeit CX 7 Manual

20
Zoom out
Zoom in
Previous page
1/60
Next page
20
Assembly Instructions
Remove all the separate parts from the packaging, lay them on the floor
and check that all are there on the basis of the assembling steps. Please
note that a number of parts have been connected directly to the main
frame and preassembled. In addition, there are several other individual
parts that have been attached to separate units. This will make it easier
and quicker for you to assemble the equipment. Assembly time ap-
prox. 60min.
Step 1:
Attach the stabilizer (45+55) at main frame (40).
1. Attach the front foot (45) with preassembled transportation roller (44+46)
to the main frame (40). Do this with the two screws M8x55 (41), washers
8//16 (28) and self-locking nuts M8 (43).
2. Attach the rear foot (55) with preassembled height adjustable screw
(57) to the main frame (40). Do this with the two screws (41), washers
(28) and self-locking nuts (43). After assembly has been completed, you
can compensate for minor irregularities in the floor by turning the foot
screw (57). The equipment should be set up that the equipment does
not move of its own accord during a training session.
Step 2:
Connection of cables (2+39) and assembly of support (8) at
the main frame (40).
1. Place screws M8x16 (32), washers 8//16 (28), curved washers 8//19 (33)
and spring washers for M8 (27) accessibly beside the front part of the
main frame (40).
2. Place the lower end of the support (8) against the main frame (40) and
plug the ends of the two computer cable harnesses (2+39) projecting
from (8+40) together.
(Note: The computer cable harness (2) projecting from the support (8)
must not slide into the tube, as it is required for later steps of installation.)
When joining the tubes, ensure that the cable connection will not
trapped.
3. Put one spring washer (27) and one washer (28) or curved washer (33)
on each screw (32). Push the screws (32) through the holes in the support
(8), screw into the threaded holes of the main frame (40) and tighten
firmly.
Step 3:
Installation of the footrest holder (100+103) at pedal crank (91).
1. Put the left footrest holder (103) at the pedal crank (91) on left hand
side and tighten the footrest holder (103) with washers 8//22 (14),
spring washer for M8 (27) and screw M8x20 (99) firmly. Put the screw
cover (98) onto the footrest holder (103).
2. Push the connection tube cover (31) onto left connection tube (34) into
intended position and tighten with screws M5x12 (5).
3. Install the right footrest holder (100) incl. all additionally required parts
on the right hand side of the machine as described in 1. – 2.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Christopeit CX 7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CX 7 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info