Manual Christopeit CRT 7100 (page 18 of 24) (English, German)

793027

Zoom out

Zoom in

1/24

Baery compartment

AAA baeries



The supplied computer allows the most convenient training. Every va-

lue relevant to training is displayed in a corresponding window.

From the beginning of the training session, the required me, the cur-

rent speed, the approximate calorie consumpon, the travelled distan-

ce ad the current pulse rate are displayed. All values are counted from

zero upwards. If you wish to see one value displayed constantly du-

ring training, select this with the „F“ key. If you wish to see these va-

lues in constant alternaon, select the „SCAN“ funcon. The display

then changes from one funcon to the next at intervals of approx. 6

seconds.

The computer is switched on by briey pressing the F- key or simply

by beginning training. The computer begins to register and display all

values. To stop the computer, just stop training. The computer stops all

measurements and retains the last aained values. The last aained

values in the funcons TIME, CALORIES and KM are stored for 4 min.

and training can connue with these values or to reset all funcons to

zero using the L- key.

The computer switches of automacally approx. 4 minutes aer trai-

ning is stopped.





The current speed is displayed in kilometres per hour. It is not possible

to specify a parcular value using the „E“ key. The values last aained

by this funcon are not stored. (Limit of the display: 999.9 km/h.)



The currently required me is displayed in minutes and seconds. It is

possible to specify a parcular value using the „E“ key. If a parcular

me has been specied, the remaining me is displayed. When the

specied value is aained, this is indicated by an acousc signal. The

values last aained by this funcon are stored. (Limit of the display:

99 minutes.)



The current status of the travelled distance is displayed. It is possible to

specify a parcular value using the „E“ key. If a parcular distance has

been specied, the remaining distance is displayed. When the specied

value is aained, this is indicated by an acousc signal. The values last

aained by this funcon are stored. (Limit of the display: 999,9 km.)



The current status of the consumed calories is displayed. It is possible

to specify a parcular value using the „E“ key. If a parcular consump-

on has been specied, the remaining number of calories to be consu-

med is displayed. When the specied value is aained, this is indicated

by anacousc signal. The values last aained by this funcon are sto-

red. (Limitof the display: 999,0 calories.)



The current pulse rate is displayed in beats per minute. It is possible to-

specify a parcular value using the „E“ key.

The values last aained by this funcon are not stored. (Limit of both

displays:40 – 240 pulse beats per minute.)



For pulse measurement, the two contact surfaces of the pulse measu-

ring handle unit must be gripped simultaneously. The contact surfaces

should be located centrally in the palms of the hands.



If this funcon is selected, the current values of all funcons are di-

splayed successively in a constant sequence approx. every 5 seconds.



Display of Stopmode. Presets can be set.





Pressing this key once briey makes it possible to change from one

funcon to another, i.e. the respecve funcons can be selected for

which entries can be made using the „E“ key. The currently selected

funcon is indicatedin the window.



By pressing this key once, it is possible to specify values step by step

in the respecve funcons. For this, the desired funcon must rstly

be selected using the „F“ key. Holding the key pressed acvates faster

running. When training begins, the specied values are then counted

down to zero.



When this key is pressed briey, the values chosen with the „F“ key are

reset to zero. If the key is held longer (approx. 3 seconds), all last aai-

ned values are deleted.



1. Open the baery compartment cover and then remove the used

Baeries.(If the baeries should leak remove them under increased

considering that the baery acid is not into contact with skin come and

clean the baery compartment thoroughly.)

Insert the new baeries (type (AAA) 1.5 V in the correct order and

taking into account the polarity in the baery compartment and close

the baerycover so that it clicks into place.

If the computer does not pick up immediately, the funcon should

baeries are removed for 10 seconds and re-inserted.

4. The empty baeries properly in accordance with the disposal regula

ons disposed of and do not give residual waste.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit CRT 7100 in the language / languages: English, German as an attachment in your email.

The manual is 2.92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit CRT 7100 Manual

Product: