600888
38
Zoom out
Zoom in
Previous page
1/48
Next page
Position the Opener
NOTE: A 25mm (1") board (1) is convenient for setting
an ideal door-to-rail distance (unless headroom is not
sufficient).
Raise the opener onto a stepladder. Open garage
door. Place a 25mm (1") board (1) laid flat on the top
section of door near the centerline as shown. Rest the
rail on the board.
If the raised door hits the trolley, pull down on the
trolley release arm to disconnect the inner and outer
trolley sections. The trolley can remain disconnected
until connecting door arm to trolley is completed.
1
15
114A2910B-GB
5-GB
Attach Rail to Header Bracket
Position opener on garage floor below the header
bracket. Use packing material to protect the cover.
Raise rail until holes in the header sleeve and holes in
the header bracket align. Join with clevis pin (1).
Insert ring fastener (2) to secure.
NOTE: To enable the rail to clear sectional door
springs, it may be necessary to lift opener onto a
temporary support. The opener must either be
secured to a support or held firmly in place by another
person.
2
1
14
Hang the Opener
The opener must be securely fastened to a
structural support of the garage.
Three representative installations are shown. Yours
may be different. Hanging brackets (1) should be
angled (Figure A) to provide rigid support. On finished
ceilings, (Figure B) attach a sturdy metal bracket (not
supplied) (4) to a structural support before installing
the opener. For concrete ceiling mount, (Figure C),
use concrete anchors provided.
On each side of opener measure the distance from
the opener to the structural support (or ceiling).
Cut both pieces of the hanging bracket to required
lengths. Flatten one end of each bracket and bend or
twist to fit the fastening angles. Do not bend at the
bracket holes. Drill 4,5mm (3/16") pilot holes in the
structural supports (or ceiling). Attach brackets to
supports with wood screws (2).
Lift opener and fasten to hanging brackets with screw,
lock washer and nut (3). Check to make sure rail is
centered over the door. REMOVE 25mm (1") board.
Operate door manually. If door hits the rail, raise
header bracket. Use rail grease and lubricate bottom
surface of rail (5).
A
2
1
1
3
4
2
3
4
2
3
3
C
B
4
2
1
3
5
16
Attach Emergency Release Rope
& Handle
Thread one end of rope (1) through hole in top of red
handle so "NOTICE" reads right side up as shown (3).
Secure with an overhand knot (2). Knot should be at
least 25mm (1") from end of the rope to prevent
slipping.
Thread other end of rope through hole in release arm
of the outer trolley (4). Adjust rope length so that
handle is 1,8m (6 feet) above the floor. Secure with an
overhand knot.
NOTE: If it is necessary to cut rope, heat seal cut end
with a match or lighter to prevent fraying.
2
3
4
N
O
TIC
E
2
1
17
114A2910B-DK
11-DK
Indstilling af endestop
Endestoppene anvendes til at stoppe porten på
bestemte punkter under portbevægelsen, når den
har nået den ønskede åbne- resp. lukkeposition.
Sådan programmeres endestoppene:
1. Den sorte tast (1) holdes indtrykket, indtil den gule
LED (3) begynder at blinke langsomt; så slippes
tasten.
2. Den sorte tast (1) holdes indtrykket, indtil porten har
nået den ønskede portposition ”ÅBEN.
Portpositionen justeres ved hjælp af den sorte (1)
og orangefarvede (2) tryktast. Med den sorte tast
flyttes porten OPAD, med den orangefarvede tast
flyttes porten NEDAD.
3. Tryk på den programmerede fjernbetjening (4) eller
den store tryktast på vægkontrolpanelet, der leveres
sammen med portåbneren. Hermed indstilles
endestoppet for portpositionen ’ÅBEN. Porten
lukker så helt til gulv og kører igen helt op til
portpositionen ’ÅBEN. Nu er endestopindstillingerne
indprogrammeret.
Kontrollér, at porten åbner tilstrækkelig meget til,
at din bil kan passere. Om nødvendigt foretages
en efterjustering.
4. Når endestoppene er programmeret, holder LEDen
(3) med at blinke.
OBS! Hvis porten kører tilbage, inden den har nået
gulvet skal du følge anvisningerne for manuel
indstilling af endestoppene i afsnittet ”Hvis der er
problemer?” under punkt 15. Til korrekt og endelig
indstilling af endestoppene hører også, at åbne-
og lukkekraften SKAL indstilles.
4
1
2
3
L
i
f
t
M
a
s
t
e
r
L
i
f
t
M
a
s
t
e
r
2
3
1
1
3
2
60 s
120 s
180 s
O
26
JUSTERINGER
Indstilling af åbne- og lukkekraft
Kraften, der måles på portens lukkekant, må ikke
overstige 400N (40kg). Hvis lukkekraften måles til
at være over 400N, skal Protectorsystemet
installeres, se punkt 29.
Tryktasten til indstilling af åbne- og lukkekraften
er placeret under lysafskærmingen. Ved hjælp af
kraftprogrammeringen indstilles den kraft, der er
nødvendig til at åbne og lukke porten.
1. Under afskærmningen sidder en orangefarvet
tast (2).
2. Ved at trykke to gange på den orangefarvede tast
(2) aktiveres kraftindstillingsfunktionen. LEDen (3)
blinker hurtigt.
3. Tryk på den programmerede fjernbetjening (4) eller
den store tryktast på vægkontrolpanelet, der leveres
sammen med portåbneren. Porten kører nedad til
portpositionen LUKKET. Tryk igen på
fjernbetjeningen (4); nu kører porten helt op til
portpositionen ӁBEN.
LEDen (3) ophører med at blinke, når åbne- og
lukkekraften er indprogrammeret.
Porten skal gennemkøre en hel cyklus, dvs. op og ned,
for at kraften er indstillet korrekt. Hvis
garageportåbneren ikke kan åbne og lukke porten helt,
skal du kontrollere, om porten er korrekt afbalanceret og
at den ikke binder/sidder fast noget sted.
(2x)
4
L
i
f
t
M
a
s
t
e
r
L
i
f
t
M
a
s
t
e
r
3
2
2
3
1
3
2
60 s
120 s
180 s
O
27
Afprøvning af
sikkerhedsreverseringssystemet
Afprøvningen af sikkerhedsreverseringssystemet er
meget vigtig. Garageporten skal køre tilbage, dvs.
reversere, ved kontakt med en fladt på garagegulvet
liggende 40mm høj hindring. Hvis portåbneren ikke
er rigtigt indstillet, kan garageporten under
lukningen forårsage alvorlige personskader.
Reverseringsafprøvningen og de i forbindelse
hermed eventuelt nødvendige efterjusteringen skal
foretages én gang om måneden
Fremgangsmåde: Anbring en 40mm høj hindring (1) på
gulvet under garageporten. Kør porten nedad. Porten
skal ved kontakt med hindringen køre tilbage. Stopper
porten ved en hindring, skal denne fjernes og punkt 26
Indstilling af endestop gentages. Afprøvningen
gentages.
Kører porten efter kontakt med den 40mm høje
hindring tilbage, fjernes hindringen og der foretages
en helt lukke- og åbnecyklus med porten. Porten må
ikke køre tilbage (reversere), når portpositionen
LUKKETer nået. Kører den alligevel tilbage, skal
punkterne 26 ’Indstilling af endestop’ og 27 ’Indstilling
af åbne- og lukkekraft’ gentages. Også den
automatiske sikkerhedsreverseringsfunktion skal
afprøves igen.
Hvis der anbringes en genstand med en vægt på
20kg midt på porten, må porten højst bevæge sig
500mm opad.
1
28
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chamberlain LiftMaster LM600A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chamberlain LiftMaster LM600A in the language / languages: English, German, Danish, French, Spanish as an attachment in your email.

The manual is 10,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info