600888

Chamberlain LiftMaster LM600A Manual

37
Zoom out
Zoom in
Previous page
1/48
Next page
Assemble Header Sleeve
Thread spring nut on carriage bolt until finger tight.
Insert a screwdriver tip (1) into one of the slots of the
nut ring (2) and brace it firmly against the header
sleeve. Place an open end wrench (3) on the square
end of the spring nut (4), slightly rotate nut about 1/4
turn clockwise until nut ring (2) is released against
header sleeve (5). This sets spring to optimum chain
tension. Chain may slip off sprocket if chain/belt is too
loose. If chain does slip re-tighten spring nut by turing
nut clockwise 1/2 turn. Do NOT overtighten
chain/belt.
Fasten Rail to Opener and Install
Chain/Belt
Holding chain (4) and belt (5) out of the way, slide rail
(1) onto shim (2) until rail is secure. Take the
chain/belt and wrap it around the sprocket (3). Make
sure the teeth on the sprocket have engaged the
chain/belt.
1
2
3
4
5
INSTALLATION SECTION
Wear protective goggles when working overhead to protect your eyes from injury.
Disengage all existing garage door locks to avoid damage to the garage door.
To avoid serious personal injury from entanglement, remove all ropes connected to the garage door
before installing the opener.
Installation of this product shall comply with ZH1/494, VDE 0700 Part 238, and VDE 0700 Part 1.
It is recommended that the opener be installed 2,1m (7 feet) or more above the floor where space permits.
1
2
3
4
1
2
3
5
2
1
3
2
1
3
Install the Header Bracket
NOTE: Refer to vertical center and horizontal lines
created in step 12 for proper placement of header
bracket.
A. Wall Mount: Center the header bracket (1) on the
vertical center line (2) with the bottom edge of the
header bracket on the horizontal line (4) (with the
arrow pointing toward the ceiling). Mark all of the
header bracket holes (5). Drill 4,5mm (3/16") pilot
holes and fasten the header bracket with wood
screws (3).
B. Ceiling Mount: Extend vertical center line (2) onto
the ceiling. Center the header bracket (1) on the
vertical mark no more than 150mm (6") from the
wall. Make sure the arrow is pointing toward the
opener. Mark all of the header bracket holes (5). Drill
4,5mm (3/16") pilot holes and fasten the header
bracket with wood screws (3). For concrete ceiling
mount, use concrete anchors provided.
B
150mm
(6")
1
2
3
Attach Sprocket Cover
Place sprocket cover (1) on top of the opener (2),
secure with screws (3).
10
13
5
5
2
50mm
(2")
3
1
4
A
4-GB
114A2910B-GB
9
11
Position the Header Bracket
The header bracket must be rigidly fastened to a
structural support of the garage. Reinforce the wall or
ceiling with a 40mm (1-1/2") board if necessary.
Failure to comply may result in improper operation of
safety reverse system.
You can attach the header bracket either to the header
wall (1) or to the ceiling (3). Follow the instructions which
will work best for your particular requirements. With the
door closed, mark the vertical centerline (2) of the garage
door. Extend line onto header wall above the door.
Open door to highest point of travel. Draw an intersecting
horizontal line (4) on header wall 5 cm (2") above high
point to provide travel clearance for top edge of door.
3
1
2
4
12
114A2910B-DK
12-DK
Montering af ”Protector System™”
(se tilbehør)
Installér dette tilbehør i forbindelse med alle
”Canopy”-vippeporte, Vippeport med lodret og
vandret køreskinne , porte på over 2,5 m og hvis
lukkekraften målt på underkanten af porten er på
mere end 400N (40 kg).
Efter åbneren er blevet installeret og justeret, kan
Protector-systemet installeres som ekstraudstyr.
Instruktioner leveres med dette.
Protector-systemet giver en yderligere grad af
sikkerhed mod, at små børn kommer i klemme
under garageporten.
Systemet anvender en usynlig stråle som, når den
brydes af en hindring, får en port, som er i færd med
at lukke, til at åbne og forhindrer en åben port i at
lukke og det anbefales stærkt til husejere med små
børn.
OBS! Portåbneren vil automatisk detektere Protector
Systemet, når dette er installeret. Portåbneren lukker
ikke, før sonsorerne er indjusteret.
29
Specialudsty
1. Tilslutning for dør i porten
Lysafskærmningen åbnes. Under afskærmningen
findes der ekstra lyntilslutningsklemmer.
Ringeledning tilsluttes til lyntilslutningsklemme 1
og 2.
2. Tilslutning af blinklys
Blinklyset kan installeres på et hvilket som helst
egnet sted. Tilhørende ledninger tilsluttes til
lyntilslutningsklemmerne 3 og 4. Klemme 4 er
jordforbundet.
©
L
O
C
K
L
I
G
H
T
58LM
75LM
78LM
98LM
7430E
8002E
FLA230
16200LM
770E
o
180s
120s
60s
1
3
2
30
Tilbehør
(1) Model 94330E Fjernbetjening med
enkeltfunktion
(2) Model 94333E Fjernbetjening med 3 funktioner
(3) Model 94335E Minifjernbetjeningssender med 3
funktioner
(4) Model 9747E Åbningssystem uden nøgle
(5) Model 78LM Multikontrolpanel til port
(6) Model 75E Baggrundbelyst
vægkontrolpanel
(7) Model 98LM Vægkontrolpanel med
bevægelsesmelder
(8) Model 760E Udendørs lås
(9) Model 1702E Nødudløser for lås
(10) Model 770E Protector-systemet
(11) Model FLA230 Blinklyssæt
(12) Model 1703E The Chamberlain Arm™
(13) Model 16200LM Port i port-kontakt
(14) Model MDL100LM Låseudstyr til mekanisk port
(15) Model EQLI01 Hurtigudløsning for
porthåndtag
(16) Model 9-13-1 Portforstærkning
VEJLEDNING FOR TILSLUTNING AF LEDNINGER
TIL TILBEHØR
Nøgleafbyder – til portåbnerens tilslutningsklemmer:
Rød-1 og hvid-2
Protector System™ – til portåbnerens
tilslutningsklemmer: Hvid-3 og grå-4
Vægkontrolpanel – til portåbnerens
tilslutningsklemmer: Rød-1 og hvid-2
94330E
94333E
94335E
9747E
760E
8
1702E
9
6
75LM
2
3
770E
10
11
FLA230
4
16200LM
MDL100LM
14
EQLl01
15
9-13-1
16
L
O
C
K
L
IG
H
T
78LM
5
1703E
12
LOCK
LIGHT
7
98LM
13
1
31
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chamberlain LiftMaster LM600A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chamberlain LiftMaster LM600A in the language / languages: English, German, Danish, French, Spanish as an attachment in your email.

The manual is 10,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info