600888

Chamberlain LiftMaster LM600A Manual

36
Zoom out
Zoom in
Previous page
1/48
Next page
ASSEMBLY SECTION
IMPORTANT: If you have a canopy door, you need to use the instructions packed with The Chamberlain
Arm™ Accessory in conjunction with this Owner's Manual when assembling the rail.
Completed Installation
As you proceed with the assembly, installation and adjustment procedures in this manual, you may find it helpful
to refer back to this illustration of a completed installation.
4
1
2
3
12
4
6
9
8
10
11
13
14
7
15
10
5
BEFORE YOU BEGIN:
1. Look at the wall or ceiling above the garage door. The header bracket must be securely fastened to structural
supports.
2. Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware (not
supplied) may be required.
3. Depending on your door's construction, you might need a special door arm. See your dealer.
4. Do you have an access door in addition to the garage door? If not, Model 1702E Outside Quick Release
Accessory is required. This accessory allows manual operation of the garage door from outside in case of
power failure.
(1) Header Sleeve
(2) Idler Pulley Bracket
(3) Trolley
(4) Rail
(5) Chain/Belt
(6) Hanging Bracket
(7) Power Cord
(8) Opener
(9) Light Lens
(10) Manual Release
Rope & Handle
(11) Curved Door Arm
(12) Straight Door Arm
(13) Door Bracket
and Plate
(14) Header Bracket
(15) Trolley Release Arm
3-GB
Install the Chain/Belt
Remove chain/belt from carton and lay chain out on
floor (do not allow chain/belt to twist).
A. Chain: Push pins of master link bar (3) through
chain link (4) and hole in back end of trolley (5).
Push cap (2) over pins and onto notches. Slide
clip-on spring (1) over cap and onto pin notches
until both pins are securely locked in place.
B. Belt: Hook the trolley connector (6) into the slot (7)
on the trolley (8).
Insert Chain/Belt into Rail & Assemble
Header Sleeve
Slide pulley bracket (1) and inner trolley (2) into back
(opener end) of rail assembly (3), be sure to insert
pulley bracket as shown with arrow (4) pointing
toward front (header end) of rail (5). Push bracket
toward front (header end ) of rail (5). Insert carriage
bolt (6) through header sleeve bracket (7). Loosely
thread spring nut (8) and flat washer (9) onto carriage
bolt. Insert carriage bolt (6) of header sleeve
assembly (7) into bold cut out in pulley bracket (1).
Slide header sleeve assembly (7) on to front (header
end) of rail (10).
Attach Trolley to Rail
Slide outer trolley (1) into back (opener) end of the rail
assembly (2), be sure end with trolley release arm (3)
is heading in direction of opener. Slide outer trolley
down rail until it engages with inner trolley.
A
1
3
2
4
5
7
B
6
8
4
5
3
1
2
8
7
6
1
6
7
10
9
1
3
2
6
8
114A2910B-GB
7
Assemble the Rail
Grease inside edges of rail sections using grease (1).
Place rail pieces (2) on flat surface for assembly. All
four rail sections are interchangeable. Slide rail brace
(3) onto rail section. Connect rail by sliding rail brace
onto next rail section. Tap rail assembly (4) on piece
of wood (5) until rail sections are flush. Repeat with
remaining rail sections.
4
5
2
3
2
1
5
13-DK
114A2910B-DK
NOTICE
41A2828
12B374
178B34
12C778
41A4166
4A1008
83A11
41A5414-1
12VDC
Pb
Cd
H
g
12B380
41A5639-7
10A20
41A5800
183D177
183D178
7423CR3
12C788
12C772
171A2
31D
525
41A5801-1 (1.7m)
41A5801 (2.3m)
41A5801-2 (2.5m)
41A5801-3 (3.0m)
31D537
41A5844 (2.3m)
41A5844-1 (2.5m)
41A5844-2 (3.0m)
41B4494-1
8423CR3
8430CR3
8023CR3
8025CR3
8030CR3
7017CR3
7023CR3
7030CR3
7035CR3
41B4103
41B4101-1
210C42
144
C
7
7
32
RESERVEDELE
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chamberlain LiftMaster LM600A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chamberlain LiftMaster LM600A in the language / languages: English, German, Danish, French, Spanish as an attachment in your email.

The manual is 10,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info