780081
4
Zoom out
Zoom in
Previous page
1/15
Next page
5 6
15mm
Clean the chainstay using
isopropyl alcohol. Install the
Chainstay Protector (PRO-CS-P)
by removing adhesive backing,
and xing the guard to the
frame. The bottom rearward
edge should be approximately
15mm from the edge of the Rear
Derailleur Hanger Nut.
M4 x 16mm
Fixing Screw
GU02 Base
Lightly grease supplied M4 xing screw, and
install the GU02 Base to the frame.*
Torque to 1-2Nm.
NOTE: Install
GU02 Base onto
frame prior to
installing fork.
*In some congurations E-wires
will need to be installed in
frame prior to GU02 Base.
Lightly grease Rear Derailleur Hanger Fixing Nut and install
either Rear Derailleur Hanger (DRH-WMN112) or Direct Mount
Rear Derailleur Hanger (DRH-SDM) nger tight. Final tightening
will be performed after rear wheel installation.
Install Front Derailleur Mount (FDM-0E0), and
ensure xing screws are torqued to 3Nm. For
1x systems replace with the Front Derailleur
Mount Blanking Plate (FDM-CVR).
1. Apply carbon assembly compound to both
frame and seatpost.
2. Insert Seatpost Clamp (SPC-0E0P) in frame so
it is ush with the top tube.
3. Adjust height and torque to 8Nm maximum.
Do not nal tighten rear derailleur hanger assembly
without rear wheel installed. Doing so may result
in a misaligned derailleur and poor shifting.
FRAME PREPARATION
Hold the frame using a secured seatpost only.
Clamping the top tube can damage the frame
and void your warranty.
1. Lightly grease supplied M4 xing screw.
Install the Threaded Fork Insert (QRI-THD)
and xing screw, tightening only lightly.
2. Without wheel in place, install the axle
and tighten until the ange meets the fork
dropout face, but does not compress the
fork blades.
3. Tighten the xing screw to 3Nm.
4. Remove the axle and install wheel.
Reinstall axle and tighten to 12-15Nm.
5. Remove axle and wheel, and re-torque the
xing screw to 3Nm.
DRH-SDMDRH-WMN112
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cervelo P-Series - 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cervelo P-Series - 2021 in the language / languages: English as an attachment in your email.

The manual is 5.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info