780075

Cervelo Caledonia - 2020 Manual

7
Zoom out
Zoom in
Previous page
1/19
Next page
11 12
FRAME & COMPONENT PREPARATION
50mm
Ensure the Chainstay
Guard wraps around
the inside of the
chainstay.
Accessory
Mount(Front)
includes
inserts
for Garmin
& Wahoo
computers.
Accessory Mount
Kit (Front)
MT-LM-F-004
Torque
to 2.5Nm. Torque
to 2Nm.
Torque
to 1Nm.
To install Accessory Mount (Front),
angle mount into ST31 or ST32 stem
faceplate and torque to 2Nm.
Dual faceplate
mount allows use
of computers,
cameras
and other
accessories.
For use without
accessory, clip may be
hidden, by reversing
the upper clamp.
Accessory Mount
Kit (Rear) Upper
Clamp
To install Accessory
Mount (Rear), replace
the rear upper clamp
of the seatpost
with the kit version.
Tighten to maximum
8Nm. See also
page 25.
Clean the chainstay using isopropyl alcohol. Install the
Chainstay Guard (PRO-CS-ASP) by removing adhesive
backing, and xing the guard to the frame. The bottom
rearward edge should be approximately 50mm forward
from the back of the rear dropout.
CALEDONIA FORK PREPARATION & INSTALLATION
Install 1 1/8" Preload
Compression Plug in fork
steerer.Torque to 8Nm
1. Apply grease to the bearing pockets and install
the upper and lower headset bearings into the
frame.
2. Fit the fork provided with your frame into the
head tube with the complete headset, required
spacers, and the stem.
3. Apply the minimum pressure needed to ensure
the assembly is fully seated. Mark the steerer
tube at the top of the stem.
4. Remove fork and clearly mark the fork steerer
tube at a point 4mm below the rst mark. Take
care to verify that this measurement is correct as
this denes the cut line for the steerer tube.
5. To trim fork steerer, use only a saw suitable for
cutting carbon, and a cutting guide.
6. Insert Fork Preload Compression Plug and
torque to 8Nm
1st Mark
2nd Mark /
Final Cut
Improper cutting of the steerer tube could
cause a failure that may result in severe injury
or death.
Avoid breathing the dust created during cutting
carbon composite materials.
Max.
4mm
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cervelo Caledonia - 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cervelo Caledonia - 2020 in the language / languages: English as an attachment in your email.

The manual is 8.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info