780075
6
Zoom out
Zoom in
Previous page
1/19
Next page
1. Lightly grease supplied M4 xing screw. Install
the Threaded Fork Insert (QRI-THD) and xing
screw, tightening only lightly. If installing
mudguards please refer also to page 32.
2. Without wheel in place, install the axle and
tighten until the ange meets the fork dropout
face, but does not compress the fork blades.
3. Tighten the xing screw to 3Nm.
4. Remove the axle and install wheel. Reinstall axle
and tighten to 12-15Nm.
5. Remove axle and wheel, and re-torque the xing
screw to 3Nm.
910
FRAME & COMPONENT PREPARATION
1. Slide the Seatpost Clamp Cover (SPCC-
314) onto the seatpost.
2. Apply carbon paste to the frame and
seatpost to be inserted into the frame.
3. Insert the seatpost and the Seatpost
Clamp (SPC-287A) into the frame
4. Adjust height and torque the Seatpost
Clamp to 8Nm maximum.
5. Slide down the Seat Clamp Cover to t
over the Seatpost Clamp.
Hold the frame using a secured seatpost only.
Clamping the top tube can damage the frame
and void your warranty.
If trimming is required, final
length should allow for a
minimum of 70mm of seatpost
remaining in the frame, or the
minimum insertion dimension
indicated on the seatpost,
whichever is greater. Failure
to meet this requirement, may
result in damage to the frame not
covered by warranty policy, or
serious injury to rider.
Lightly grease Rear Derailleur Hanger Fixing
Nut and install Rear Derailleur Hanger
(DRH-WMN112) nger tight. Final tightening
will be done after rear wheel installation
(page 28). If installing mudguards refer also
to page 32.
Secure the Front Derailleur
Mount (FDM-0E0) into frame
with two xing screws. Tighten
to 3Nm.
With 1x chainring
setups, use the
Blanking Plate
(FDM-CVR).
Apply grease to
the interior
sliding surfaces
of the Seatpost
Clamp wedge.
Do not final tighten rear derailleur
hanger assembly without rear wheel
installed. Doing so will result in a
misaligned derailleur and poor shifting.
1. Apply carbon paste to
the frame and seatpost
to be inserted into the
frame.
2. Insert the seatpost into
the frame.
3. Adjust height and torque
the Seatpost Clamp (SPC-
SQ-R-2011-A) to 6Nm
maximum.
Note: For Caledonia
seatpost installation:
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cervelo Caledonia - 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cervelo Caledonia - 2020 in the language / languages: English as an attachment in your email.

The manual is 8.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info