624481
6
Zoom out
Zoom in
Previous page
1/9
Next page
Operation Guide 5240
E-59
To enter and exit the Stopwatch Mode
In the Timekeeping Mode, press C twice to enter the Stopwatch Mode.
The
x
b
Lower Dial Hand will move to ST.
To perform an elapsed time operation
A
A A A B
Start Stop (Restart) (Stop) Zero Reset
To perform fl yback timing
Pressing B while an elapsed time operation is in progress performs zero reset and
immediately resumes timing from there. You can do this as many times as you want.
A
B B
.....
A B
Start 1 Start 2 Start 3 Stop Zero Reset
An ongoing elapsed time measurement operation is not affected by pulling out the x
crown.
E-58
Using the Stopwatch
You can use the stopwatch to measure elapsed times. A fl yback feature (page E-59)
lets you reset the stopwatch to zero without stopping time measurement.
Hands and Indicators
z
Hour Hand: Indicates the stopwatch minute count
(1 revolution = 60 minutes).
x
Second Hand: Indicates the 0.05-second count during
stopwatch operation.
c
Minute Hand: Indicates the stopwatch seconds count.
v
Upper Dial Hand: Indicates the stopwatch minute count
(1 revolution = 120 minutes).
b
Lower Dial Hand: Points to ST.

* B
@+ >
E-57
To swap your Home City and World Time City
In the World Time Mode, hold down A for about three
seconds until the watch beeps.
This indicates that your Home City and World Time City
x
have been swapped.
After swapping the Home City and World Time City, the x
watch will stay in the World Time Mode. The
x
Second
Hand will point to your new World Time City (TYO in this
example).
Note
If your current World Time City supports time calibration
x
signal reception, making it your Home City enables
calibration signal reception for that city.

@
E-56
After selecting the city you want, push the crown back in to return to the World 5.
Time Mode.
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
capability can come in handy when you frequently travel between two locations in
different time zones.
The following example shows what happens when the
Home City and World Time City are swapped while the
Home City originally is TYO (Tokyo) and the World Time
City is NYC (New York).
Home City World Time City
Before
swapping
Tokyo
10:08 p.m.
(Standard time)
New York
9:08 a.m.
(Daylight saving time)
After
swapping
New York
9:08 a.m.
(Daylight saving time)
Tokyo
10:08 p.m.
(Standard time)

@
E-55
Rotate the crown to move the 3.
x
Second Hand to the city code you want to select
as the World Time City.
Each time you select a city code, the
z
Hour Hand,
c
Minute Hand,
v
Upper
Dial Hand, and
n
Day Indicator move to the current time and day for that city
code. For details about city codes, see the “City Code Table” at the back of this
manual.
If you think that the time indicated for the selected World Time City is not correct,
it probably means that there is something wrong with your Home City settings.
Use the procedure under “To confi gure Home City settings” (page E-34) to
correct the Home City settings.
Hold down 4. A for about one second to cycle through the summer time settings as
shown below.
AA
AT (AUTO) STD DST
A
E-54
Important!
Time calibration signal reception is disabled while the watch is in the World Time
x
Mode.
To view the time in another time zone
In the Timekeeping Mode, press 1. C once to enter the World Time Mode.
The
x
b
Lower Dial Hand will move to WT.
To select the UTC zone as your World Time, simply hold down x B for about three
seconds. No other operation is required.
Pull out the crown.2.
The
x
x
Second Hand points to the currently selected World Time city code.
The x
b
Lower Dial Hand will indicate AT (AUTO), STD (standard time) or DST
(daylight saving time), which indicates the current daylight saving time setting.
If you do not perform any operation with the crown for about two minutes after
x
pulling it out, crown operations will become disabled and the watch hands will no
longer move when you rotate the crown. If this happens, push the crown back in
and then pull it out again.
E-53
Checking the Current Time in a Different Time Zone
You can use World Time to view the current time in one of 29 time zones around the
globe. The currently selected city is called the “World Time City”.
Hands and Indicators
z
Hour Hand and
v
Upper Dial Hand:
Indicate the hour of the current time in the World Time
City.
x
Second Hand:
Indicates the current World Time City for about three
seconds after the World Time mode is entered.
c
Minute Hand:
Indicates the current minute in the World Time City.
b
Lower Dial Hand: Points to WT.
n
Day Indicator
Pressing
A causes the
x
Second Hand to move to the
current World Time City for about three seconds.

+
6B *
@ >
NYC (NEW YORK)
E-52
Temperature Reading Precautions
Body temperature, direct sunlight, and humidity all have an effect on temperature
readings. To help ensure more accurate temperature readings, remove the watch
from your wrist, wipe it dry of any moisture, and place it in a well-ventilated location
not exposed to direct sunlight for about 20 to 30 minutes before taking temperature
readings.
E-51
Important!
To cancel a temperature reading correction setting, hold down
x A and B at the
same time. The watch will beep.
Push the crown back in.3.
After about ten seconds, regular timekeeping will resume.
x
Important!
If you do not perform any operation with the crown for about two minutes after
x
pulling it out, crown operations will become disabled and the watch hands will no
longer move when you rotate the crown. If this happens, push the crown back in
and then pull it out again.
E-50
Important!
The watch will not be able to produce correct temperature readings if you make a
x
mistake during the correction procedure. Check to make sure that the value you
use for correction produces correct temperature readings.
Before performing the following procedure, remove the watch from your wrist and
x
leave it for about 20 or 30 minutes to allow the case temperature to become the
same as the air temperature.
While the hands are indicating a temperature reading, pull out the crown.1.
Rotate the crown to adjust the temperature setting. 2.
Holding down A and B at the same time will return the temperature reading to the
factory default setting.
Each rotation of the crown moves the hands by 1°C (2°F).
x
You can adjust the temperature reading within the range of –10 to 60°C (or 14 x
to 140°F).
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 5240 - GW-A1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5240 - GW-A1000 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5240 - GW-A1000

Casio 5240 - GW-A1000 User Manual - German - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info