480779
6
Zoom out
Zoom in
Previous page
1/16
Next page
When using an earlier scala rider headset as a Passenger
headset, Voice Connect Intercom can be initiated only by
the scala rider Q2
pro
headset.
Manual Connect Intercom can be initiated from either
headset by pressing the MC button for scala rider Q2
pro
and CTRL button for any earlier scala rider headset.
RESET INTERCOM PAIRING
You can delete all of the headset’s Intercom pairings at any time.
1. With the scala rider Q2
pro
headset turned ON, press and hold the
CTRL Button for at least six seconds until the Red and Blue Lights
begin rapidly alternating.
2. Press and hold the Volume Up Button for three seconds.
3. The Red and Blue Lights will ash ve times simultaneously
and then the headset will turn o, conrming that Reset was
successfully completed.
SET UP FOR MOBILE PHONE CALLS:
PAIRING
If you have a Bluetooth enabled mobile phone and would like to
make and receive phone calls using the scala rider Q2
pro
, you must
rst pair your headset to the mobile phone.
NOTE: If you have a compatible Bluetooth GPS device you wish to use
with the scala rider Q2
pro
, please skip this step, and continue ahead
to SET UP FOR BLUETOOTH GPS DEVICE.
Pairing is a one time process. Once the headset is paired to a
specific mobile phone during this Setup Procedure, they will
remain paired and automatically recognize each other whenever
they are within range. If the connection between the phone and
headset is lost, tap the CTRL button to reconnect the devices.
To Pair the scala rider Q2
pro
to a Bluetooth Mobile
Phone
1. Turn on your phone and make sure its Bluetooth function is
activated.
2. With the scala rider Q2
pro
headset turned ON, press and
hold the CTRL Button for at least six seconds until the Red and
Blue Lights begin rapidly alternating.
3. Search for Bluetooth devices on your phone by following the
phone’s instructions. Please consult your phone’s User Manual
for more information.
4. After a few seconds the phone will list the
“scala rider Q2
Pro
as a discovered device. Select it and follow your phones
instructions to accept the pairing.
5. When prompted enter 0000 (four zeros) as your PIN or passkey.
6. Your phone will conrm that pairing has succeeded and the
headset will begin ashing slowly in Blue.
NOTE: If the Pairing process is not completed within two minutes the
headset will return to Standby mode.
With some mobile phones, you may need to tap the CTRL button
to connect the headset to the phone after pairing is complete. The
scala rider Q2
pro
headset will automatically connect to the last
phone connected to the headset.
SET UP FOR BLUETOOTH GPS DEVICE:
PAIRING
If you have a Bluetooth enabled GPS device and would like to transmit
navigation instructions and sounds from the GPS device through the
headset’s speakers, you mustrst pair your headset to the GPS device.
NOTE: Not all Bluetooth enabled GPS devices allow connections to
Bluetooth headsets like the scala rider Q2
pro
. Please consult your
GPS device’s User Manual for more information.
6
scala rider
®
Q2
pro
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cardo Scala rider Q2 Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cardo Scala rider Q2 Pro in the language / languages: English as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cardo Scala rider Q2 Pro

Cardo Scala rider Q2 Pro User Manual - German - 15 pages

Cardo Scala rider Q2 Pro User Manual - Dutch - 15 pages

Cardo Scala rider Q2 Pro User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info