480779
8
Zoom out
Zoom in
Previous page
1/16
Next page
1. Use the enclosed Allen Wrench to remove both Allen
screws and release the Helmet Clamp’s back plate.
2. Determine the location on the helmet where the
Helmet Clamp must be attached.
3. Adjust the Helmet Clamp’s location on the Hel-
met so that the microphone is located opposite
your mouth. You may need to reposition the
Clamp repeatedly until you identify the best spot. The microphone
must be positioned vertically and not horizontally (Be sure to clean
the selected area prior to the gluing process).
4. Use the pre-moistened Towelette to clean the helmet area where
you want to install the Glue Plate. Allow to dry thoroughly.
5. Peel the foil cover from the Glue Plates’ adhesive pad.
6. Place the Glue Plate into position according to #3. Press rmly 15
seconds on all 3 parts of the Glue Plate.
7. The adhesive pad bonds to full strength over the next 24 hours.
Therefore it is recommended to not use the headset during this 24
hour period.
8. Fasten the Clamp to the Glue Plate using the Allen screws that were
previously removed.
If you have purchased a helmet clamp version with the corded
microphone, please proceed as follows:
ATTACHING THE CORDED MICROPHONE CLAMP ON A
FULL-FACED HELMET
If you are using the corded microphone version, you must rst make sure
your helmet clamp is attached to your helmet as
described in previous section (ATTACHING THE
CLAMP ON THE HELMET). Clean the exact spot on
the internal padding of the helmet, opposite your
mouth, where the microphone will be placed and
proceed as follows.
a. Peel the foil cover from the adhesive Velcro
pad and place the Velcro pad on the chosen
location opposite your mouth.
b. Attach the microphone to the Velcro, as
shown in photo.
c. When done, tighten the screws of the clamp
POSITIONING THE SPEAKERS
Speaker A
Speaker B
Attach the speakers to the Velcro inside
your helmet opposite your ears (short
speaker cord for the left ear [A] and the
long speaker cord [B] for the right ear).
You may want to use the supplied Velcro
pad.
Speaker A
Speaker B
Speaker B
Cable
Using two speakers inside the
helmet may be prohibited in
certain jurisdictions. If this is the
case, you should tuck away the
long corded speaker underneath
the helmet padding as follows:
Lead the speaker cord [B] along-
side the rim of the padding to
the right side and then back
to the left side, near speaker
[A]. Then place the speaker [B]
underneath the padding.
8
scala rider
®
Q2
pro
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cardo Scala rider Q2 Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cardo Scala rider Q2 Pro in the language / languages: English as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cardo Scala rider Q2 Pro

Cardo Scala rider Q2 Pro User Manual - German - 15 pages

Cardo Scala rider Q2 Pro User Manual - Dutch - 15 pages

Cardo Scala rider Q2 Pro User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info