Manual Cardo Scala rider G4 (page 15 of 27) (English)

480782

Zoom out

Zoom in

1/27

English

Since the G4 can be paired with all models in the scala rider family,

we recommend that you rst pair it according to your preferred

conguration and then change or modify as often as you wish later,

when the need arises. For example: If you typically use the intercom

to communicate with two friends who both use G4 units, then you

should pair it as described below in section 9.10 b.

Therefore, please select your initial pairing preference from the

following options in the table below and then refer to the pairing

procedure as described in the respective section of this manual.

When done, return to the explanations in section 9.4 “Initiate

Intercom Calls”.

Select your preferred Pairing Option

UNITS TO BE PAIRED

GO TO

SECTION

Your G4 with another G4 9.10 a

Your G4 with a Q2/Q2 pro 9.11 a

Your G4 with one earlier scala rider model 9.11 b

Your G4 with two other G4 units 9.10 b

Your G4 with one G4 and one Q2/Q2 pro unit 9.11 c

Your G4 with two Q2/Q2 pro units 9.11 c

Your G4 with one G4 and one other scala rider model 9.11 c

Your G4 with one Q2/Q2 pro and one other scala rider

model

9.11 c

Your G4 with two other scala rider models 9.11 c

Your G4 as part of 4-Way intercom call conguration 9.10 c

9.4 INITIATE INTERCOM CALLS

Now that you have completed the pairing process, you can start using the

intercom. If you haven’t done so yet, please refer to the table above and

complete your preferred pairing conguration before you proceed with

this section.

There are two ways to start an Intercom call with devices that are paired to

your scala rider G4 (make sure you are in Standby mode):

VOICE CONNECT:

Preferred for relatively brief conversations as

it takes the channel into standby mode after

30 seconds of silence.

Start talking loudly

Once you start talking loudly, an

Intercom call will be established with

both paired devices, CHANNEL “A” and

CHANNEL “B” (if both are available).

The Intercom call will stay on until

all participants remain silent for

30 seconds. (applicable for 2-way

communication).

CHANNEL BUTTON CONNECT:

Preferred for extended

conversations as it leaves the

channel open and active.

Single tap the CHANNEL

“A” Button to add or remove

CHANNEL “A” from an Intercom

call.

Single tap the CHANNEL

“B” Button to add or remove

CHANNEL “B” from an Intercom

call.

NOTE: While the Intercom is on, the Redial and Voice Dial functions will be

disabled.

9.5 RECEIVING INTERCOM CALLS

Once another paired device tries calling you via intercom, the call will

begin almost instantly.

NOTE: The G4’s preset priority modes have been set in a way to avoid

incoming intercom calls from interrupting mobile phone calls and GPS

instructions in progress. In such case the intercom caller will hear a busy

signal and you will hear two beeps, indicating that an intercom caller is

trying to page you. (see section 4.3 for details on audio priorities of paired

devices).

scala rider

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cardo Scala rider G4 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cardo Scala rider G4

Cardo Scala rider G4 User Manual - German - 30 pages

Cardo Scala rider G4 User Manual - Dutch - 29 pages

Cardo Scala rider G4 User Manual - French - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cardo Scala rider G4 Manual

Product: