480782
7
Zoom out
Zoom in
Previous page
1/27
Next page
English
NOTE: While we have no reason to believe that the gluing option might
negatively aect any helmet, Cardo does not assume any responsibility
to that eect, irrespective of its nature and circumstances. The Glue Plate
is oered as an option that you may choose to use at your own risk and
subject to renouncement of any future claims.
1. Use the enclosed Allen Wrench to remove
both Allen screws and release the Helmet
Clamp’s back plate.
2. Determine the location on the helmet where the Helmet Clamp
must be attached.
3. Adjust the Helmet Clamp’s location on the Helmet so that the
microphone is located opposite the center of
your mouth. You may need to reposition the
Clamp repeatedly until you identify the best
spot. (Be sure to clean the selected area prior to
the gluing process).
4. Use the pre-moistened Towlette to clean the helmet area where
you want to install the Glue Plate. Allow to dry thoroughly.
5. Peel the foil cover from the Glue Plate’s adhesive pad.
6. Place the Glue Plate into position according to #3. Press rmly 15
seconds on all 3 parts of the Glue Plate.
7. The adhesive pad bonds to full strength over the next 24 hours.
Therefore we recommend not using the G4 during this 24 hour
period.
8. Fasten the Clamp to the Glue Plate using the Allen screws that
were previously removed.
If you have purchased a helmet clamp version with the corded
microphone, please proceed as follows:
5.2 ATTACHING THE CORDED MICROPHONE TO A
FULLFACED HELMET
If you are using the corded microphone version, you must rst make
sure your helmet clamp is attached to your
helmet as described in previous section (5.1).
Clean the exact spot on the internal padding of
the helmet, opposite your mouth, where the
microphone will be placed.
a. Peel the foil cover from the adhesive Velcro
pad and place the Velcro pad on the chosen
location opposite your mouth.
b. Attach the microphone to the Velcro, as shown
in photo.
c. When done, tighten the screws of the clamp.
5.3 POSITIONING THE MICROPHONE AND SPEAKERS
Speaker A
Speaker B
The microphone must be positioned in front of
the center of your mouth as detailed above.
Attach the speakers to the Velcro inside your
helmet, opposite your ears (short speaker
cord for left ear & long speaker cord for right
ear). Use the supplied Velcro pads if needed.
Using two speakers inside the
helmet may be prohibited in certain
jurisdictions. If this is the case, you
should tuck away the long corded
speaker underneath the helmet
padding as follows:
Speaker A
Speaker
B
Speaker B
Cable
Lead the speaker cord [B] alongside the
rim of the padding to the right side
and then back to the left side, near
speaker [A]. Then place the speaker
[B] underneath the padding.
7
scala rider
®
G4
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cardo Scala rider G4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cardo Scala rider G4 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cardo Scala rider G4

Cardo Scala rider G4 User Manual - German - 30 pages

Cardo Scala rider G4 User Manual - Dutch - 29 pages

Cardo Scala rider G4 User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info