816489

Carat VZ-500 Manual

12
Zoom out
Zoom in
Previous page
1/33
Next page
RVZ-500 Operation manual
page 12 03/2021
4.2.2. Fastening of the Cutting Disc
1. Turn off the engine and open the disc cover.
2. Use the enclosed wrenches to hold the
spindle and unscrew the fastening nut.
NOTE: Left thread!
3. Fit the cutting disc on the spindle and secure
it. Pay attention to the right sense of
direction – see arrow on disc.
4. Close the disc cover and secure it.
Fig. Location of wrenches
4.2.3. Cutting
1. Have the disc raised above floor.
2. Disengage the emergency button (counter
clockwise)
3. On/off switch on motor in on-position
4. Start the motor with the recoil and set to full
throttle.
5. Open the water tap to engage sprinkling.
6. Move the machine to the beginning of the
cut.
7. Lower slowly the disc into the cut, till
required cutting depth is reached.
8. Sensitively push the machine forward and
follow the marked path (use the guide).
9. The machine can only cut in straight
direction. In case the direction must be
changed, raise the disc from the cut, take
new direction and lower the disc again.
7. At the end of the cut, raise the disc, set the
throttle to idle.
NOTE! Check the water level in the tank and
timely add water if necessary.
For optimal service life of the cutting disc, the
operator should work carefully and sensitively.
Do not force the machine!
Nevertheless, lifetime of the disc may vary
depending on the material to be cut and other
factors.
4.2.4. Cutting Depth Scale
Cutter RVZ-500 has a cutting depth scale. Use
the scale as follows:
1. Lower the disc just to touch the ground. In
this position, adjust the "zero" using the
wing nuts below the scale.
2. Alternatively you can just remember the value
on the scale and then add or subtract required
cutting depth as necessary.
4.3. Engine Turning-Off
1. Shift the throttle control lever to idle
position.
2. Let the engine run idle for a while to cool
down.
3. Push emergency stop button
4. Turn the on/off switch to "OFF" position.
5. Close the fuel tap
4.4. Handling, Transport, Storing
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat VZ-500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat VZ-500 in the language / languages: English as an attachment in your email.

The manual is 1.94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info