816472
16
Zoom out
Zoom in
Previous page
1/24
Next page
16
The electromotor starts up, but the diamond cutting
blade doesn’t turn:
1. Check if the bolt is tightened sufficiently on the flange
set.
2. Check if the gear wheel transmission functions well.
Turn around the driven sha and attentively listen
if the armature revolves simultaneously. If not, please
contact a specialist to check the machine.
The diamond cutting blade is running but swings:
1. Check if the flanges and the centre of the diamond
cutting blade are clean. Remove visible dirt.
2. Check the straightness of the diamond cutting blade.
In case of doubt contact your supplier.
3. In case of oscillation by clearance on the bearing
or a crooked sha, contact the supplier. Working with
a swinging blade can lead to dangerous situations.
The diamond cutting blade cuts too slowly.
1. Check the saw depth. Cutting in concrete or stone has
to be done in steps of 2,5 to 5 cm. Depending of the
hardness of the stone (medium hard, abrasive stone
material) a 5 until 8 cm saw depth is possible.
2. The diamond cutting blade is blunt. The diamond
grains are worn out and not sticking out of the metal
bonding. Check this by scratching your nail at the
edge of the diamond cutting blade. In case of a blunt
blade you feel a polished surface. You can easily
solve this problem by making some cuts into an
abrasive stone material. A special grindstone is
available.
The diamond cutting blade gets blunt from:
1. The power of the motor can go down by using
extension cables. The saw speed also goes down and
the diamond cutting blade becomes blunt. Do not use
extension cables longer than 30 meter. A minimum
thickness of 2,5 mm² is necessary. In case of using
cable drums these need to be unrolled completely.
2. The type of blade is not suitable for the material to be
sawn. You need a dierent kind of blade for cutting
concrete or hard stone and cutting abrasive materials.
Please contact the supplier for a professional advice.
3. The direction of the rotation of the diamond cutting
blade does not correspond with the direction on the
machine. Depending on the time length of the incor
rect use, the direction of the diamond cutting blade
must be changed or contact the supplier for a profes-
sional advice.
4. The diamond cutting blade does not rotate centrical-
ly. By pushing the diamond cutting blade into
the material, the diamond textures will break and
the diamond cutting blade becomes blunt. When
the diamond cutting blade is worn out eccentric the
manufacturer has the possibility to make it centric
again.
WARRANTY
For the machine, a guarantee period of 12 months applies
from the moment of delivery. Guarantee claims must be
shown by submission of purchase invoice. The guarantee
includes the repair of defects which have occurred and can
be linked by to material or manufacturing faults.
Not covered by guarantee:
Not covered by guarantee:
Defects or damages which have arisen due to incorrect use
or connection.
Machine overload.
When maintenance has been carried out incorrectly or
badly.
Information in the manual has not been properly
followed.
The machine is used by unqualified persons.
If the machine is used for purposes for which it is
unsuitable.
The machine is repaired using unoriginal parts.
If the machine encryption is damaged or deleted.
If defects are caused by fire, damp and/or transport.
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
is in conformity with the following standards or standard-
ized documents:
EN 60745-1; EN 61000; 2006/42/CE; 2014/30/CE; 2002/95/CE
EN 12100:2010
EN 14121-2:2012
EN 13857: 2008
EN 1005-2: 2003
EN 1005-4: 2005
EN 60204-1:2006
EN 60529:1992/A1:2000
EN 61000-6-2: 2005
EN 61000-6-4:2006+A1:2011
Director: C.J. van Beek
01-02-2021
CARAT Nederland B.V.
Nikkelstraat 18, 4823 AB Breda, Nederland
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat MZ-350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat MZ-350 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 1.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info