816472
14
Zoom out
Zoom in
Previous page
1/24
Next page
14
manipulate the vacuum hose. When rocks or chunks of
stone/masonry are drawn into the vacuum hose, cease
work and clean the vacuum hose immediately. Prevent
the vacuum hose from being bent or creased.
Use the wall saw machine only as intended for.
Observe the general requirements for construction sites.
Provide for good ventilation.
Ensure that the work area is free of obstructions. For
longer grinding jobs, the vacuum cleaner must be able to
move along freely and at the right time.
Wear hearing protection, protective goggles, a dust mask
and gloves as required. As dust mask, use at least a
particle-filtering class FFP 2 half-mask.
Use a suitable vacuum cleaner for cleaning the work-
place. Prevent settled dust from being swirled up by
sweeping.
ASSEMBLY INSTRUCTIONS
Necessary tools:
• Wrench 6 mm.
• Screwdriver or pin.
To install the diamond cutting blade follow next steps (see
page 4, image A):
• Disconnect from the power supply.
• Loosen the depth locking leaver (#10).
• Remove the flange cover from the blade guard.
• Move the motor until the flange with bolt appears before
the hole.
Loosen the bolt with the delivered wrench and remove
the flange. It is possible that the bolt is stuck. In that case:
use a pin or screwdriver between the diamond cutting
blade’s teeth to block the axle, and loosen the bolt.
Check the condition of the flange set. The surfaces
between the flange and the diamond cutting blade need
to be clean and must fit exactly.
Mount the new diamond cutting blade. Please pay
attention to the direction of rotation. The direction on
the diamond cutting blade has to be identical to the
machine’s rotation direction.
Mount the flange on the axle.
Screw the bolt in the axle.
Prevent the diamond cutting blade from turning by
blocking it with a screwdriver or pin between the teeth of
the diamond cutting blade and tighten the bolt.
Use the same procedure to change a worn diamond
cutting blade.
OPERATION INSTRUCTIONS
Before cutting in a wall, floor or similar object: investigate
whether the object contains any electric, water or gas
conduits. If necessary, use a locator for detecting conduits
in the object.
Only use diamond cutting blades.
It is strictly forbidden to use other blades, like circular
woods blades, because the extra necessary protection fails.
Do not use deformed, damaged or bad diamond cutting
blade.
The voltage of the wall socket must be similar to the
voltage indicated on the machine.
To prevent unintentional starts, the wall saw machine is
provided with a lock-o button (#12).
For further use of the machine please check the safe-
guards for proper functioning. In case of damage to the
case or other parts, these need to be repaired or repla- ced
by a professional service department. Don’t use other
equipment that cannot be flawlessly switched ON and OFF.
While using, please hold the machine with both hands
Starting the machine:
Connect to the power supply.
Press the lock-o button (#12).
Press the main ON/OFF switch (#13).
Release the switch (#13 ) to turn the machine OFF.
Adjust the cutting depth.
The depth of the cut needs to be adapted to
of the hardness of the material to be cut.
Using the machine as followed will prevent
any overload.
Cutting in concrete has to be done in steps of 2,5 to 5 cm
of depth; so for instance: a depth of 12 cm depth can be
reached in 2 or 3 steps. Cut brick in steps of 5 to 8 cm,
depending on the hardness of the stone.
Adjust the cutting depth:
• Disconnect from the power supply.
• Loosen the depth locking leaver (#10).
• Adjust the saw depth by moving the motor along the rails.
• Lock the depth locking leaver (#10).
Use the right diamond cutting blade.
Choose a type of diamond cutting blade which is suitable
for the material to be sawn. We advice CARAT diamond
cutting blades. Please read all the instructions of the dia-
mond cutting blades.
Make sure that the diamond cutting blade is turning in the
right direction. Check the arrow on the blade guard for the
correct direction.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat MZ-350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat MZ-350 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 1.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info