816479

Carat MultiCoup 350 Manual

21
Zoom out
Zoom in
Previous page
1/80
Next page
21
ENGLISH
6.3 Start-up
The machine is switched on by the main switch. For this
purpose, press the green button to start.

In dry cutting process, the dust extractor must be
switched on.
In wet cutting process, the cooling water must be trans-
ported in suicient quantities to the cutting wheel and
drain o on both sides.
If these are not the case, stop machine immediately!
6.4 Cuttingoperation
 
1. When cutting in 90° position, the cutter head remains
at a fixed point. For adjustment, proceed as follows:
2. Switch of the machine -> the cutting wheel must stop
rotating!
3. Loosen the adjusting screw.
4. Set the cutter head in the desired position.
5. Tighten the adjusting screw -> check if the cutter head
is adjusted in height and make sure that it cannot
move.
6. Put the material to be cut onto the table (for table saw
machine position it directly at the material stop).
7. Check the position of the material using the angle stop.
8. Start the motor. If using wet cutting, open the ball
valve for the water supply.
9. Grasp the handle of the cutting head with your right
hand and the transport handle on the frame with your
le hand.
10. Then slowly slide the cutter head through the material
to be cut without pressure. The cutting wheel then
cuts through the material on the table.







The machine oers the possibility of performing 45° bevel
cuts. To perform 45° bevel cuts, proceed as follows:
1. 1. Switch o the machine -> the cutting wheel must
stop rotating!
2. Pull the cutting material table forward to have room
for turning the cutting head.
3. Loosen the nut at the back of the cutting head.
4. Swivel the cutting head until it reaches the 45 °posi-
tion.
5. Tighten the nut firmly at the back of the cutting head.
6. Fix the cutting head with the locking lever in the lowest
position.
7. Place the material to be cut on the cut material table
and position it directly at the material stop.
8. Start the motor. If using wet cutting, open the ball
valve for the water supply.
9. Grasp the handle of the cutting head with your right
hand and the transport handle on the frame with your
le hand.
10. Slide the cutting material table slowly, without pres-
sure, forward to the cutting disc and pull it back again
aer cutting through the cut material.







To bring back the cutter head to the 90° position aer 45°
bevel cuts, proceed as follows:
1. Switch o the machine -> the cutting wheel must stop
rotating!
2. Loosen the locking lever and fix the cutting head again
in the top position.
3. Loosen the nut at the back of the cutting head.
4. Swivel the cutting head until it reaches the 90 °position.
5. Tighten the nut firmly at the back of the cutting head
6. Fix the cutting head again with the locking lever.








 
Heavily polluted water decreases the service life of the
cutting wheel.
For frequent use, change water several times a day, and
collect, filter and dispose of the cutting mud.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat MultiCoup 350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat MultiCoup 350 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 14.67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info