816479

Carat MultiCoup 350 Manual

20
Zoom out
Zoom in
Previous page
1/80
Next page
20
In case of storage for over 3 months, check general
condition of all parts and packaging on a regular basis. If
necessary, renew or replace conservation materials.
 


Improper transportation can result in considerable dam-
age of the machine and objects in the vicinity.
Before every transport:
- The cutter head must be locked.
- The cutter head must be lowered and locked.
- The machine must be disconnected from power supply.
The machine can be carried by one person on the vertical
column.




 
5.1 Connection
Before connecting the machine to the power source,
make sure that:
- Voltage / phase of the power supply, match the data on
the type plate of the motor and machine.
- The power supply line is grounded according to the
safety provisions.
- The wire size of the extension cord is suicient, H07RNF
3x2.5 mm² up to 50m for 230V.
5.2 Mountingadiamondblade
To mount a new diamond blade or replace the used one,
proceed as follows:
1. Switch o the machine and interrupt the power supply
by pulling the mains cable from the mains outlet.
2. Loosen the screw on the back of cutting wheel guard
so as to be able to turn the blade guard aside.
3. Loosen the nut of the motor sha and remove the
outer cutter flange.
4. Clean the cutter flange, nut and motor sha.
5. Check the parts for signs of wear.
6. Mount or replace the diamond blade. While doing so,
pay attention to the correct rotation direction of the
diamond blade and motor sha.
7. Replace the outer cutting flange on the motor sha.
8. Screw the nut onto the motor sha again and tighten it
firmly.
9. Turn the cutting wheel guard back to its original loca-
tion.
10. Tighten firmly the screws on the back of cutting wheel
guard.






 
6.1 Intendedworkingpositionoftheoperator
The operator takes position in front of the machine.
The operator stands in front of the machine so that he
can push the cutting material table forward and back and
adjust the cutting head appropriately.
6.2 Start-uppreparation
To safely use the machine as intended, the following
preconditions must be met:
- The machine stands firmly.
- The water supply via a pressurized water tank or a
standing pipe is guaranteed, or a suitable dust extractor
of class M is connected to the dry cutting method.
- The machine has been checked for damage, loose screw
connections and integrity.
- The water supply is functional.
- Rotation direction arrows on the cutting wheel and
guard match.
- An appropriate cutting wheel must be installed, which
meets optimum conditions.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat MultiCoup 350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat MultiCoup 350 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 14.67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info