750733

Cambridge SoundWorks Desktop Theater 5.1 DTT2500 Digital Manual

10
Zoom out
Zoom in
Previous page
1/26
Next page
6
Speaker Wire and Stand Installation
Typically, the 3 meter speaker
cables will connect the front and
center satellites to the Decoder
Amplifier and the 5 meter cables
will connect the rear satellites to
the Decoder Amplifier. A panel of
twelve self-adhesive labels is
provided to identify each satellite
and subwoofer and the opposite
end of the cable connected to a
satellite and subwoofer.
1. Identify a 3 meter cable. Most
often, a satellite will be used
with a desktop stand. In this
case, thread the bare wire end of
a 3 meter cable through the hole
in the desktop stand. Connect
this end to a satellite (as shown
in Diagram K). Carefully insert
the desktop stand’s attachment
arm into the socket in the back
of the satellite, taking up any
slack in the cable as required.
2. To use this satellite in the front
left position, remove the backing
from the small, round “L” label
and apply it to the back of the
satellite (see Diagram K).
3. Remove the backing from the
remaining, longer “L” label and
wrap it around the opposite end
of the speaker cable near the
RCA-type plug.
4. Place the satellite in the front
left position.
5. Repeat this process using
another 3 meter cable for the
front right satellite, using the
“R” labels.
6. Connect another 3 meter cable to
a satellite. Use the “C” (center)
labels. If used, the Monitor
Stand attaches to the satellite in
the same manner as the
Desktop Stands, although it
does not have a hole for the
speaker wire. Route the wire to
the left or right side of the
attachment strut. Position the
satellite.
7. If you wish to use the Floor
Stands with the rear satellites,
assemble the stand according to
Attaching The Floor Stand
instructions on page 7. Use the
RS and LS labels (right and left
surround) and 5 meter cables.
8. Connect the subwoofer using the
last 3 meter cable to the “SUB”
labels.
Diagram K: To connect the
speaker wire to each satellite,
press one of the spring-loaded tabs
to expose the connection hole.
Insert the bare end of the wire
into the exposed hole, then release
the tab to lock the wire in place.
Connect wires with red bands to
red tab connectors, and unmarked
wires to black tab connectors.
Notes: Matching red wires to red
tabs and unmarked wires to black
tabs insures the speakers all play
“in phase”. “Out-of-phase”
connections will do no electrical
harm, but the overall sound
quality will be greatly reduced.
You can substitute regular 18
gauge speaker wire to create
longer cables, if needed.
K
DOLBY DIGITAL
(AC-3) SPDIF IN
SPEAKER OUTPUTS
LINE IN REAR IN
C SUBWOOFER RS LS R L
15V
DC IN
DIGITAL
DIN ANALOG AUTO
INPUT
SUBWOOFER
LINE OUT
C
SUB
RS
LS
R
C
SUB RS LS
R
C
SUB
RS
LS
R
REAR
RIGHT
L
L
0420000547 REV. B SINGLE 2/9/01, 1:50 PM10
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cambridge SoundWorks Desktop Theater 5.1 DTT2500 Digital at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cambridge SoundWorks Desktop Theater 5.1 DTT2500 Digital in the language / languages: English as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info