697437
17
Zoom out
Zoom in
Previous page
1/52
Next page
4
Installation
Logano GE615 - Subject to technical modifications.
17
Fig. 16 Boiler compression tool 2.3
1 Threaded connection on the pull rods (loosened)
2 Threaded connection on the pull rods (correct position)
Fig. 17 shows the central section with flow connection.
The nipples for fitting the next central section are inserted
into the corresponding hubs. The packing cord has
already been inserted into the packing groove. As with the
rear section (Æ Fig. 12, page 15), there is also a break in
the elastic packing cord here. The boiler section has been
equipped with foot wedges for ease of installation. The
boiler section foot wedges are also used later for final
levelling of the boiler block.
Fig. 17 Using the boiler section foot wedges
1 Packing cord (with break)
2 Boiler section foot wedge
Assemble all other boiler sections as described. The front
section is fitted last.
B Insert the anchor rods (with spring packs fitted) into the
cast lugs on the top left and right and bottom left and
right, next to the boiler block hubs.
B Put a nut onto each of the threaded anchor rods and
tighten by hand.
B Now tighten the nuts on the anchor rods 1 to 1½ turns.
B Level the boiler block vertically and horizontally on the
base/silencing plinth (Æ see Chapter 4.3.1, page 12).
Use the boiler section foot wedges provided for this
purpose (Æ Fig. 17, page 17).
B Remove boiler compression tool.
Fig. 18 Inserting the anchor rods
1 Anchor rods (bottom)
2 Anchor rods (top)
3 Anchor rod with spring pack
The next step describes the installation of the feed pipe
(Æ see Chapter 4.6, page 18).
After the front section is attached, loosen the
compression tool but do not remove it. Insert
the anchor rods first.
NOTICE: Damage to system through
excessively low contact pressure.
B Do not compress the spring pack. Only
use the spring pack in its original state.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Buderus Logano GE615 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Buderus Logano GE615 in the language / languages: English as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Buderus Logano GE615

Buderus Logano GE615 User Manual - German - 12 pages

Buderus Logano GE615 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info