666606

Bruder Mannesmann 1595 Manual

10
Zoom out
Zoom in
Previous page
1/27
Next page
11. Release the trigger; this will automatically release the the spent rivet pin, and you are
ready for the next rivet.
12. Immediately empty the safety cap if full.
13. Disconnect the tool from the compressed air supply and pull the trigger to release any
remaining compressed air from the tool before changing the nosepiece, if not in use,
after you complete your work, or before servicing your air hydraulic riveter.
Replacing the nosepiece
1. Disconnect the tool from the compressed air supply and pull the trigger a few times to
allow any remaining compressed air to escape.
2. Screw the new nosepiece into the frame head. The frame head is spring loaded, so
make sure that the nosepiece does not jump out. Screwing in a nosepiece for larger rivet
pin diameters may be a little difficult due to the heavy spring resistance. These
nosepieces have a longer design and push the jaws backwards to allow you to insert a
thicker rivet pin between the jaws.
Tip: You can make it easier to fit the nosepiece by removing the frame head before screwing
the nosepiece into it, then screwing the frame head complete with the nosepiece back onto
your riveter.
Air pressure and air volume
• Your riveter should be operated at a pressure of 6.5 bar; pressures more than the the
maximum allowable pressure of 8 bar will increase the load on your riveter and shorten
its life. Use a compressor with an air volume of at least 200 L/min to power your air
hydraulic riveter.
• Always use air hoses with an inner diameter of at least 9 mm. When adjusting the air
pressure, keep in mind that the pressure will fall by around 0.6 bar at a hose length of 10
m and inner diameter of 9 mm.
Maintenance and care
• Conscientious lubrication and care are essential towards ensuring proper operation and
long life.
• You will need a clean air supply to operate a pneumatic tool. Corrosion residues, dust
and dirt from the air supply line will affect performance and cause technical problems. A
lubricating unit with a filter, reducing valve and oiler connected between the air supply
and riveter will remove moisture and dirt from the air, regulate operating pressure and
ensure optimal tool lubrication.
• Clean your device with a damp cloth if necessary.
• Do not use chemical cleaning agents that contain strong organic solvents such as spirits,
thinners or similar, as they may damage the plastic.
• Do not let liquids into the tool or immerse the tool in liquid. Water in the air supply may
cause damage to the tool. Drain any water from your compressor or pneumatic system
on a regular basis.
• Clean the air filter in your pneumatic system at least once a week.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bruder Mannesmann 1595 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bruder Mannesmann 1595 in the language / languages: English, German as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info