Manual Brother Innov-is M280D (page 91 of 100) (English)

718769

Zoom out

Zoom in

1/100

Troubleshooting

APPENDIX

Error messages

When erroneous operations are performed messages and advice on operation will be displayed on the LCD. Follow what is

displayed. If you press or do the operation correctly while the error message is displayed, the message disappears.

Error messages Cause/solution

A malfunction occurred. Turn the machine off, then

on again.

This message is displayed if some malfunction occurs.

Turn the machine off, then back on again.

If this message continues to appear, the machine may be malfunctioning.

Please contact your authorized Brother dealer or the nearest Brother

authorized service center.

Cannot change the configuration of the characters. This message is displayed when there are too many characters and the

curved character configuration is impossible.

Cannot change the font since some letters are not

included to the selected font.

This message appears when the font of the embroidery character pattern is

changed to one that does not include characters used in the pattern.

Cannot recognize the data for the selected pattern.

The data may be corrupted. Please turn off the

power and turn on again.

This message appears when you try to retrieve pattern data that is invalid.

Since any of the following may be the cause, check the pattern data.

• The pattern data is damaged.

• The data that you tried to retrieve was created using another

manufacturer’s data design system.

Turn the machine off, then on again to return it to its normal condition.

Check and rethread the upper thread. This message is displayed when the upper thread is broken or not threaded

correctly, and the “Start/Stop” button, etc. is pressed.

Data volume is too large for this pattern. This message is displayed when the patterns you are editing take up too

much memory, or if you are editing too many patterns for the memory.

Lower the buttonhole lever. This message is displayed when the buttonhole lever is up, a buttonhole

stitch is selected, and the “Start/Stop” button, etc. is pressed.

Lower the presser foot lever. This message is displayed when a button, such as the “Start/Stop” button,

was pressed while the presser foot was raised.

No more patterns can be added to this

combination.

This message is displayed when you tried to combine more than 70

decorative stitches.

Not enough available memory to save. This message is displayed when the memory is full and the stitch or pattern

cannot be saved.

Not enough available memory to save the pattern.

Delete another pattern?

This message is displayed when the memory is full and the stitch or pattern

cannot be saved.

Press and delete a previously saved stitch or pattern to save the current

one.

Press to return to the original screen without saving.

OK to recall and resume previous memory? This message appears if the machine is turned off while embroidering, then

turned on again.

Press to return the machine to the condition (pattern position and

number of stitches) when it was turned off. Follow the procedure described

in “If the thread breaks or the bobbin runs out of thread during embroidering”

on page 69 to align the needle position and embroider the remainder of the

pattern.

Pattern extends to the outside of embroidery frame. This message appears when the selected embroidery pattern is larger than

the embroidery frame selected when [Embroidery Frame Identification View]

is set to [ON].

Pattern extends to the outside of embroidery frame.

Add no additional characters.

This message is displayed when the character pattern combination is too

large to fit in the embroidery frame. Change the character pattern size or

layout the patterns to fit the embroidery frame. If [Embroidery Frame

Identification View] is set to [ON], setting to [OFF] or selecting larger frame

may help.

Pattern extends to the outside of embroidery frame.

This function cannot be used at this time.

This message appears when the embroidery character pattern is resized or

switched between written vertically/horizontally so that it is too large for the

embroidery frame.

bonjour
je dois faire des coutures au point droit à 5mm du bord. comment faire le réglage. Merci Submitted on 15-11-2022 at 10:03
Reply Report abuse
bonjour
je souhaite faire des coutures à 0.5 cm avec ma brother 280. Comment faire
Merci bonne journée Submitted on 3-9-2022 at 10:38
Reply Report abuse
message sur brother 280 lorsque la commande de vitesse est réglée pour contrôler la largeur du point zigzag, la touche marche/arrêt ne fonctionne pas. Comment faire pour annuler cette commande Merci de m'aider Submitted on 27-5-2022 at 07:10
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is M280D in the language / languages: English as an attachment in your email.

The manual is 5,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is M280D

Brother Innov-is M280D User Manual - German - 100 pages

Brother Innov-is M280D User Manual - Dutch - 100 pages

Brother Innov-is M280D User Manual - French - 100 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brother Innov-is M280D Manual

Product: