Manual Brother Innov-is M280D (page 17 of 100) (English)

718769

Zoom out

Zoom in

1/100

Winding/Installing the Bobbin

GETTING READY

Pass the thread under the hook on the bobbin winding

thread guide, and then wind it counterclockwise under

the pretension disk.

1 Bobbin winding thread guide

2 Pretension disk

3 Pull it in as far as possible

Wind the thread clockwise around the bobbin 5 or 6

times, pass the thread through the guide slit in the

bobbin winder seat, and then pull the thread to cut it.

1 Guide slit in bobbin winder seat

(with built-in cutter)

Slide the sewing speed controller to adjust the bobbin

winding speed. Slide the controller to the right to

increase the speed; slide it to the left to reduce the

speed.

Turn on the machine.

Press the “Start/Stop” button once to start winding the

bobbin.

When the foot controller is plugged in, press down on

the foot controller.

When the bobbin winding becomes slow, press the

“Start/Stop” button once to stop the machine.

When the foot controller is plugged in, remove your

foot from the foot controller.

Cut the thread, slide the bobbin winder shaft to the left

until it snaps into place, and then remove the bobbin.

Slide the sewing speed controller to desired sewing

speed position.

Remove the spool for the bobbin thread from the spool

pin.

Note

• Make sure that the thread is passed under the

pretension disk.

Note

• Be sure to wind the thread clockwise around the

bobbin, otherwise the thread will become wrapped

around the bobbin winder shaft.

CAUTION

• Be sure to cut the thread as described. If the

bobbin is wound without cutting the thread

using the cutter built into the guide slit in the

bobbin winder seat, the thread may become

tangled in the bobbin or the needle may bend

or break when the bobbin thread starts to run

out.

Memo

• We recommend winding stretch thread, such as

transparent nylon thread, at a low speed since the

thread may stretch.

Note

• When winding transparent nylon thread on the bobbin,

stop bobbin winding when the bobbin is 1/2 to 2/3 full. If

the bobbin was fully wound with transparent nylon

thread, it may not be wound neatly, or sewing

performance may suffer. In addition, extreme pressure

may be applied to the bobbin, it may not be possible to

remove the bobbin from the bobbin winder shaft, or the

bobbin may break.

CAUTION

• When the bobbin winding becomes slow, stop

the machine, otherwise the machine may be

damaged.

bonjour
je dois faire des coutures au point droit à 5mm du bord. comment faire le réglage. Merci Submitted on 15-11-2022 at 10:03
Reply Report abuse
bonjour
je souhaite faire des coutures à 0.5 cm avec ma brother 280. Comment faire
Merci bonne journée Submitted on 3-9-2022 at 10:38
Reply Report abuse
message sur brother 280 lorsque la commande de vitesse est réglée pour contrôler la largeur du point zigzag, la touche marche/arrêt ne fonctionne pas. Comment faire pour annuler cette commande Merci de m'aider Submitted on 27-5-2022 at 07:10
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is M280D in the language / languages: English as an attachment in your email.

The manual is 5,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is M280D

Brother Innov-is M280D User Manual - German - 100 pages

Brother Innov-is M280D User Manual - Dutch - 100 pages

Brother Innov-is M280D User Manual - French - 100 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brother Innov-is M280D Manual

Product: