718769

Brother Innov-is M280D Manual

15
Zoom out
Zoom in
Previous page
1/100
Next page
Winding/Installing the Bobbin
GETTING READY
13
1
Adjusting input sensitivity for operation keys
You can adjust the sensitivity of the operation keys to 5 levels.
Display the settings screen to set desired level.
a
Press to display the settings screen.
b
Display page 7 by pressing / .
c
Press [Start].
The adjusting screen is displayed.
d
Adjust the [Input Sensitivity] by pressing / .
• The higher the setting, the more sensitive the keys
will be. The default setting is [3].
• We recommend selecting the highest setting if an
electrostatic touch pen is being used.
• While adjusting the input sensitivity, press to
check whether the key responds.
When the key responds, the setting value indicating
the sensitivity blinks.
e
Press to return to previous screen.
■ If the machine does not respond when an
operation key is pressed
Turn machine off, then hold down (Thread cutter
button) and turn on the machine to reset [Input
Sensitivity]. Display the settings screen, and then adjust
the [Input Sensitivity] again.
Winding the bobbin
This section describes how to wind thread onto a bobbin.
a
Place the bobbin on the bobbin winder shaft so that the
notch in the bobbin aligns with the spring on the shaft,
and then slide the bobbin winder shaft to the right until
it snaps into place.
• The “Start/Stop” button lights up in orange.
b
Remove the spool cap and place the spool of thread for
the bobbin onto the spool pin.
Slide the spool onto the spool pin so that the thread
unwinds to the front from the bottom. Otherwise the
thread may become tangled around the spool pin.
1 The thread unwinds to the front from the bottom.
Winding/Installing the Bobbin
CAUTION
• Only use the plastic bobbin that comes with
this machine or bobbins of the same type
(SA156/SFB: XA5539-151/SFB). The bobbin's
height is 11.5 mm (approx. 7/16 inch). Using
other bobbins may cause damage to the
machine. SA156 is Class 15 type bobbin.
Memo
• When winding the bobbin for sewing utility stitches, use
thread appropriate for the fabric that you wish to sew
(page 21). Normally, the thread will be the same as what
is used for the upper threading.
• When winding bobbin for embroidery, be sure to use the
recommended 60 weight embroidery bobbin thread for
this machine.
1 Notch
2 Bobbin winder
shaft spring
2
1
1
… 15 …


Need help? Post your question in this forum.

Forumrules
1

Forum

brother-innov-is-m280d

Reset search

  • bonjour
    je dois faire des coutures au point droit à 5mm du bord. comment faire le réglage. Merci Submitted on 15-11-2022 at 10:03

    Reply Report abuse

  • bonjour
    je souhaite faire des coutures à 0.5 cm avec ma brother 280. Comment faire
    Merci bonne journée Submitted on 3-9-2022 at 10:38

    Reply Report abuse

  • message sur brother 280 lorsque la commande de vitesse est réglée pour contrôler la largeur du point zigzag, la touche marche/arrêt ne fonctionne pas. Comment faire pour annuler cette commande Merci de m'aider Submitted on 27-5-2022 at 07:10

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is M280D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is M280D in the language / languages: English as an attachment in your email.

The manual is 5,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is M280D

Brother Innov-is M280D User Manual - German - 100 pages

Brother Innov-is M280D User Manual - Dutch - 100 pages

Brother Innov-is M280D User Manual - French - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info