718739
121
Zoom out
Zoom in
Previous page
1/132
Next page
Troubleshooting
Appendix A-19
MAINTENANCE AND TROUBLESHOOTING
A
Fabric does not
feed through the
machine.
Feed dogs are set in the down position. Slide the feed dog position switch to the right
.
B-2
Stitches are too close together. Lengthen the stitch length setting. B-38
Wrong presser foot was used. Use the correct presser foot. B-30
Needle is turned, bent or the point is dull. Replace the needle. B-27
Thread is entangled. Cut the entangled thread and remove it from the
race.
A-8
Zigzag foot “J” is slanted on a thick seam at the
beginning of stitching.
Use the presser foot locking pin (black button
on the left side) on zigzag foot “J” to keep the
presser foot level while sewing.
S-4
Presser foot pressure is set incorrectly for
fabric.
Adjust the presser foot pressure with the
presser foot pressure dial.
B-41
The fabric feeds in
the opposite
direction.
The feed mechanism is damaged. Contact your authorized Brother dealer or the
nearest Brother authorized service center.
The needle
contacts the
needle plate.
The needle clamp screw is loose. Firmly tighten the needle clamp screw. If the
needle is bent or blunt, replace it with a new
one.
B-27
Needle is turned, bent or the point is dull. Replace the needle. B-27
Fabric being sewn
with the machine
cannot be
removed.
Thread is tangled below the needle plate. Lift up the fabric and cut the threads below it,
and clean the race.
A-8
A broken needle
has fallen into the
machine.
Turn off the machine, and then remove the
needle plate. If the needle that fell into the
machine can be seen, use tweezers to remove
it. After removing the needle, return the needle
plate to its original position and insert a new
needle.
Before turning on the machine, slowly turn the
handwheel toward you to check that it turns
smoothly and that the new needle enters
through the center of the needle plate opening.
If the handwheel does not turn smoothly or the
needle that fell into the machine cannot be
removed, contact your authorized Brother
dealer or the nearest Brother authorized service
center.
A-8
The handwheel
feels sluggish
when it is turned.
Thread is tangled in the bobbin case. Remove the tangled thread from the bobbin
case. Re-install the bobbin case so it is
correctly positioned.
A-6, A-8
The stitch is not
sewn correctly.
The presser foot that is used is not appropriate
for the type of stitch that you wish to sew.
Attach the presser foot that is appropriate for
the type of stitch that you wish to sew.
B-30
The thread tension is incorrect. Adjust the tension of the upper thread. B-39, A-7
The thread is tangled, for example, in the
bobbin case.
Remove the tangle thread. If the thread is
tangled in the bobbin case, clean the race.
A-8
Feed dogs are set in the down position. Slide the feed dog position switch to the right
.
B-2
Symptom Probable Cause Remedy Reference
121


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is F410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is F410 in the language / languages: English as an attachment in your email.

The manual is 3,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is F410

Brother Innov-is F410 User Manual - German - 132 pages

Brother Innov-is F410 User Manual - Dutch - 132 pages

Brother Innov-is F410 User Manual - French - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info