718739
119
Zoom out
Zoom in
Previous page
1/132
Next page
Troubleshooting
Appendix A-17
MAINTENANCE AND TROUBLESHOOTING
A
Needle breaks.
Stitch length is too short. Adjust the stitch length. B-38
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-13
Upper thread
breaks.
Machine is not threaded correctly (used the
wrong spool cap, spool cap is loose, the thread
did not catch the needle bar threader, etc.).
Rethread the machine correctly. B-19
Knotted or tangled thread is being used. Remove any knots or tangles.
The selected needle is not appropriate for the
thread being used.
Select a needle that is appropriate for the type
of thread being used.
B-26
Upper thread tension is too tight. Adjust the thread tension. B-39
Thread is tangled. Use scissors, etc., to cut the tangled thread and
remove it from the race, etc.
A-6
Needle is turned, bent or the point is dull. Replace the needle. B-27
Needle is installed incorrectly. Reinstall the needle correctly. B-27
There are scratches around the opening in the
needle plate.
* There is a notch on the left side of the
opening in the needle plate. This is not a
scratch.
1 Notch
Replace the needle plate, or consult your
authorized Brother dealer.
A-8
There are scratches around the opening in the
presser foot.
Replace the presser foot, or consult your
authorized Brother dealer.
B-29
There are scratches on the bobbin case. Replace the bobbin case, or consult your
authorized Brother dealer.
A-2
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-26
While sewing, the thread became knotted or
tangled.
Rethread upper and lower thread. B-13, B-19
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-13
The thread is
tangled on the
wrong side of the
fabric.
Upper threading is incorrect. Check the steps for threading the machine and
rethread the machine.
Be sure that the presser foot is in the raised
position when threading the machine so that the
upper thread sets properly in the upper tension.
B-19, A-6
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-26
The upper thread is
too tight.
The bobbin thread is incorrectly installed. Correctly install the bobbin thread. B-16, A-5
Symptom Probable Cause Remedy Reference
a
119


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is F410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is F410 in the language / languages: English as an attachment in your email.

The manual is 3,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is F410

Brother Innov-is F410 User Manual - German - 132 pages

Brother Innov-is F410 User Manual - Dutch - 132 pages

Brother Innov-is F410 User Manual - French - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info