718734
16
Zoom out
Zoom in
Previous page
1/76
Next page
Winding/Installing the Bobbin
14
g
Slide the sewing speed controller to adjust the bobbin
winding speed. Slide the controller to the right to
increase the speed; slide it to the left to reduce the
speed.
h
Turn on the machine.
i
Press the “Start/Stop” button once to start winding the
bobbin.
When the foot controller is plugged in, press down on
the foot controller.
j
When the bobbin winding becomes slow, press the
“Start/Stop” button once to stop the machine.
When the foot controller is plugged in, remove your
foot from the foot controller.
k
Cut the thread, slide the bobbin winder shaft to the left
until it snaps into place, and then remove the bobbin.
l
Slide the sewing speed controller to desired sewing
speed position.
m
Remove the spool for the bobbin thread from the spool
pin.
Installing the bobbin
Install the bobbin wound with thread.
You can begin sewing immediately without pulling up the
bobbin thread by simply inserting the bobbin in the bobbin
case and guiding the thread through the slit in the needle
plate cover.
a
Turn on the machine.
b
Press (Needle position button) once or twice to
raise the needle.
c
Lower the presser foot lever.
d
Press .
If is pressed while the presser foot is raised, an
error message appears. Lower the presser foot lever
and press again.
The screen changes, and all keys and operation
buttons are locked (except ).
e
Raise the presser foot lever.
Memo
We recommend winding stretch thread, such as
transparent nylon thread, at a low speed since the
thread may stretch.
Note
When winding transparent nylon thread on the bobbin,
stop bobbin winding when the bobbin is 1/2 to 2/3 full. If
the bobbin was fully wound with transparent nylon
thread, it may not be wound neatly, or sewing
performance may suffer. In addition, extreme pressure
may be applied to the bobbin, it may not be possible to
remove the bobbin from the bobbin winder shaft, or the
bobbin may break.
CAUTION
When the bobbin winding becomes slow, stop
the machine, otherwise the machine may be
damaged.
Memo
If the threads will be pulled to create gathers or the
thread at the beginning of sewing will be finished, for
example, when free motion quilting, first pull up the
bobbin thread.
For details, refer to “Pulling up the bobbin thread” on
page 18.
CAUTION
Use a bobbin that has been correctly wound
with thread, otherwise the needle may break
or the thread tension will be incorrect.
Before inserting or changing the bobbin, be
sure to press on the operation panel to
lock all keys and buttons, otherwise injuries
may occur if the “Start/Stop” button or any
other button is pressed and the machine starts.
16


Need help? Post your question in this forum.

Forumrules
1

Forum

brother-innov-is-a150

Reset search

  • Please How do you change the speed controller mode to "off" ? Submitted on 26-1-2022 at 02:13

    Reply Report abuse
  • Please Have do you change the speed controller mode to "off" ? Submitted on 26-1-2022 at 01:58

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is A150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is A150 in the language / languages: English as an attachment in your email.

The manual is 2,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is A150

Brother Innov-is A150 User Manual - German - 76 pages

Brother Innov-is A150 User Manual - Dutch - 76 pages

Brother Innov-is A150 User Manual - French - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info