718734
15
Zoom out
Zoom in
Previous page
1/76
Next page
Winding/Installing the Bobbin
GETTING READY
13
1
b
Remove the spool cap and place the spool of thread for
the bobbin onto the spool pin.
Slide the spool onto the spool pin so that the thread
unwinds to the front from the bottom. Otherwise the
thread may become tangled around the spool pin.
1 The thread unwinds to the front from the bottom.
c
Slide the spool cap onto the spool pin.
Slide the spool cap as far as possible to the right, as
shown, with the rounded side on the left.
d
Pass the thread under the thread guide, then under the
thread guide cover and to the front.
1 Thread guide
2 Thread guide cover
e
Pass the thread under the hook on the bobbin winding
thread guide, and then wind it counterclockwise under
the pretension disk.
1 Bobbin winding thread guide
2 Pretension disk
3 Pull it in as far as possible
f
Wind the thread clockwise around the bobbin 5 or 6
times, pass the thread through the guide slit in the
bobbin winder seat, and then pull the thread to cut it.
1 Guide slit in bobbin winder seat
(with built-in cutter)
CAUTION
If the spool or the spool cap is not installed
correctly, the thread may become tangled
around the spool pin, causing the needle to
break.
Three spool cap sizes are available, allowing
you to choose a spool cap that best fits the size
of spool being used. If the spool cap is too
small for the spool being used, the thread may
catch on the slit in the spool or the machine
may be damaged.
For more information, refer to “Memo” on
page 13.
Memo
When using the spool as shown below, use the small
spool cap, and leave a small space between the cap
and the spool.
When using thread that winds off quickly, such as
transparent nylon thread or metallic thread, place the
spool net over the spool before placing the spool of
thread onto the spool pin.
If the spool net is too long, fold it to fit the size of the
spool.
1
1 Spool cap (small)
2 Spool (cross-wound
thread)
3 Space
2
1
3
Note
Make sure that the thread is passed under the
pretension disk.
Note
Be sure to wind the thread clockwise around the
bobbin, otherwise the thread will become wrapped
around the bobbin winder shaft.
CAUTION
Be sure to cut the thread as described. If the
bobbin is wound without cutting the thread
using the cutter built into the guide slit in the
bobbin winder seat, the thread may become
tangled in the bobbin or the needle may bend
or break when the bobbin thread starts to run
out.
a
b
1
2
3
a
15


Need help? Post your question in this forum.

Forumrules
1

Forum

brother-innov-is-a150

Reset search

  • Please How do you change the speed controller mode to "off" ? Submitted on 26-1-2022 at 02:13

    Reply Report abuse
  • Please Have do you change the speed controller mode to "off" ? Submitted on 26-1-2022 at 01:58

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is A150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is A150 in the language / languages: English as an attachment in your email.

The manual is 2,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is A150

Brother Innov-is A150 User Manual - German - 76 pages

Brother Innov-is A150 User Manual - Dutch - 76 pages

Brother Innov-is A150 User Manual - French - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info