718734
14
Zoom out
Zoom in
Previous page
1/76
Next page
Winding/Installing the Bobbin
12
F When set [ON], reinforcement stitches are sewn at the
beginning and/or end of sewing for a reinforcement
stitch pattern, even when the reverse button is pressed.
(page 27)
G Select the level of the input sensitivity for operation keys.
(page 12)
H Selects the display language.
I Displays the program version.
Adjusting input sensitivity for operation keys
You can adjust the sensitivity of the operation keys to 5 levels.
Display the settings screen to set desired level.
a
Press , display the seventh page of the settings
screen, and then press to select (Input
Sensitivity).
b
Adjust the input sensitivity by pressing .
The higher the setting, the more sensitive the keys will
be. The default setting is [3].
We recommend selecting the highest setting if an
electrostatic touch pen is being used.
While adjusting the input sensitivity, press any of the
numeric keys to check the sensitivity. When the key
responds, the setting value indicating the sensitivity
blinks.
If the machine does not respond when an
operation key is pressed
Turn machine off, then hold down (Needle position
button) and turn on the machine to reset the settings.
Display the settings screen, and then adjust the settings
again.
Winding the bobbin
This section describes how to wind thread onto a bobbin.
a
Place the bobbin on the bobbin winder shaft so that the
notch in the bobbin aligns with the spring on the shaft,
and then slide the bobbin winder shaft to the right until
it snaps into place.
F
G
H
I
Winding/Installing the Bobbin
CAUTION
Only use the plastic bobbin that comes with
this machine or bobbins of the same type
(SA156/SFB: XA5539-151/SFB). The bobbin's
height is 11.5 mm (approx. 7/16 inch). Using
other bobbins may cause damage to the
machine. SA156 is Class 15 type bobbin.
Bobbins previously manufactured may not
have the “b” mark on the bobbin. However,
they can be used with this machine if they are
the same type (SA156/SFB: XA5539-151/SFB).
1 Notch in the
bobbin
2 Bobbin winder
shaft spring
Memo
Checking the installation orientation of the bobbin will
be helpful in later procedures. By placing the bobbin
into the bobbin case in the same orientation that it was
on the bobbin winder shaft, the bobbin can be installed
with the correct winding direction of the bobbin thread.
The “b” mark on one side of the bobbin included with
this machine can be used as a reference.
2
1
14


Need help? Post your question in this forum.

Forumrules
1

Forum

brother-innov-is-a150

Reset search

  • Please How do you change the speed controller mode to "off" ? Submitted on 26-1-2022 at 02:13

    Reply Report abuse
  • Please Have do you change the speed controller mode to "off" ? Submitted on 26-1-2022 at 01:58

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is A150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is A150 in the language / languages: English as an attachment in your email.

The manual is 2,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is A150

Brother Innov-is A150 User Manual - German - 76 pages

Brother Innov-is A150 User Manual - Dutch - 76 pages

Brother Innov-is A150 User Manual - French - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info