Manual Brita 3-Way Water Filter Dispenser (page 4 of 13) (English)

504591

Zoom out

Zoom in

1/13

ENGLISH 3

3 BRITA 3-Way Water Filter Dispenser –

easy installation

Before starting, please check that you have all the components

listed above (see ﬁ g. 1) as well as the recommended tools.

There are 7 steps to the installation.

Prior to installation, read the Technical Data (chapter 7) and

the Important Information (chapter 9). The system cannot

be installed with a low pressure boiler as this might lead to

water damages.

After storage and transport below 0°C, the product must be

stored in the open original packaging for at least 24 hours at

the stated ambient temperatures (chapter 7) for operation.

3.1 Step 1: Selecting the carbonate hardness

setting (++/+) on the ﬁ lter head

The ﬁ lter head has been set to meet most European water con-

ditions. In some soft water areas though, you may wish to adjust

the ﬁ lter head to your local settings. To do so, ﬁ rst carry out a

carbonate test using the supplied testing strip. The strip can be

found in the outer wrapping of these Usage Instructions.

Using the testing strip:

• Let the red response ﬁ eld of the probe soak in a glass of your

tap water for 1 second (ﬁ g. 2).

• After 1 minute, compare the colour of the response ﬁ eld with

the table and read the appropriate setting from the table.

Depending on the colour of the testing strip, we recommend

setting your ﬁ lter head as follows:

Setting + ++

Colour

Red, orange,

yellow

Green, dark

green

Capacity 1000 L 500 L

German Carbonate

Hardness [°dH]

up to 8.5 above 8.5

English Carbonate

Hardness [°eH]

up to 10.6 above 10.6

Setting + ++

French Carbonate

Hardness [°fH]

up to 15.2 above 15.2

Grains per Gallon CaCO3

[gpg CaCO3]

up to 8.9 above 8.9

Milligram per Litre CaCO3

[mg/L CaO3]

up to 151 above 151

The ﬁ lter head is set to “++” by default. To change the setting,

use an Allen key (4 mm). Turn in the direction of the arrow until

the “+” appears in the window (ﬁ g. 3).

The ﬁ lter head contains a ﬂ ow regulator already installed which

guarantees smooth water ﬂ ow from your dispenser even at higher

water pressures.

3.2 Step 2: Starting the BRITA electronic

cartridge exchange indicator

A Commissioning:

Please insert the enclosed batteries (2 x AA) into the appropriate

compartment of the BRITA electronic cartridge exchange indicator

with display. A long beep will sound after insertion of the batteries.

B Initial programming with ++ or + setting (see step 1):

Important: The BRITA electronic cartridge exchange indicator has

been set to 90 days to co-ordinate with the cartridge ﬁ ltration set-

ting of “++”. Both of these default settings will deliver optimum

ﬁ ltration performance for most water conditions.

Caution: Please, ensure that you activate the electronic BRITA

cartridge exchange indicator with display during the day so that the

signal can start during the day.

Initial programming with ++ setting (see ﬁ g. 4):

a Press the DISPLAY button brieﬂ y to activate the display. Initially,

the default setting of 90 days is displayed.

b Then press the START/RESET button brieﬂ y to activate the

90-day timer.

c A ﬂ ashing spot in the bottom left of the display indicates that the

timer has begun.

Initial programming with + setting (see ﬁ g. 4):

a Press the DISPLAY button brieﬂ y to activate the display. Initially,

the default setting of 90 days is displayed.

b Press and hold the DISPLAY button and then press the

START/RESET button brieﬂ y at the same time. This activates

the setting mode.

(ﬁ g. 2)

(ﬁ g. 3)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brita 3-Way Water Filter Dispenser in the language / languages: English as an attachment in your email.

The manual is 5,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brita 3-Way Water Filter Dispenser Manual

Product: