697430
24
Zoom out
Zoom in
Previous page
1/48
Next page
Installation
Uni Condens 8000 F – 6720867056 (2016/10)
24
6.14 Installing the temperature sensor
NOTICE:
System damage through damaged capillaries or incorrectly fitted
temperature sensor.
Ensure that the capillaries are neither kinked nor squashed when
uncoiling and routing them.
Always push the temperature sensor right to the bottom of the sensor
pocket.
NOTICE:
System damage due to incorrect sensor position!
The sensors of the high limit safety cut-out (STB) and of the thermostat
(TR) must be fitted at the installation location ( fig. 23, page 24) on
the top of the boiler.
In the case of third party control units, match the sensor immersion
sleeve to the diameter of the sensors used.
Do not change the length of the immersion sleeve.
The boiler test point is at the top of the boiler shell
( fig. 23, [1], page 24).
Measure the depth of the sensor pocket ¾ ".
Mark the depth on the temperature sensor set (cable).
Insert the temperature sensor set as far as it will go into the test
point (to the bottom).
Use the mark to check whether the temperature sensors are correctly
fitted.
Secure the temperature sensor set in the test point with a sensor
retainer [3] ( fig. 22, page 24).
The plastic coil [2] for keeping the temperature sensors together is
pushed back automatically when it is inserted ( fig. 22, page 24).
Insert compensating spring [1] between the temperature sensors to
ensure a good contact between sensor pocket [4] and sensor surfaces,
and thereby a reliable temperature transfer ( fig. 22, page 24).
Fig. 22 Inserting the plastic coil into the sensor pocket
[1] Compensating spring
[2] KPlastic coil
[3] Sensor retainer
[4] Sensor well
Never kink excess lengths of capillaries.
Route the sensor lead to the control unit.
Connect the sensor lead to the control unit.
6.15 Routing the burner cable
Route the burner cable along the door hinge side
(factory-fitted on the right).
Route the burner cable [5] from below, behind the control unit
support, to the control unit.
Connect burner cable [5] to control unit [3].
Secure the burner cable with the external strain relief.
Route the burner cable from the control unit to the burner.
Connect burner cable [5] to the burner using the burner plug.
Fig. 23 Fitting the burner cable
[1] Temperature sensor immersion sleeve
[2] Cable conduit
[3] Control unit
[4] Strain relief
[5] Burner cable
010011598-002
1
2
3
4
0010014755-001
2
1
3
4
5
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Uni Condens 8000 F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Uni Condens 8000 F in the language / languages: English as an attachment in your email.

The manual is 10,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch Uni Condens 8000 F

Bosch Uni Condens 8000 F User Manual - English - 12 pages

Bosch Uni Condens 8000 F User Manual - German - 16 pages

Bosch Uni Condens 8000 F User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info