697430
22
Zoom out
Zoom in
Previous page
1/48
Next page
Installation
Uni Condens 8000 F – 6720867056 (2016/10)
22
6.10.2 Fitting the burner to the burner plate
DANGER:
Injury/system damage through excess loads.
Use suitable lifting gear for mounting the burner.
WARNING:
Damage to health, including skin and eye irritation, as a result of
inhaling or coming into contact with fibre dust.
Fibre dust may be inhaled when working on the thermal insulation and
insulating rings.
Wear a breathing mask and protective glasses with side shields when
working on the thermal insulation.
Wear gloves and clothing that is loose-fitting around the neck and
wrists. Clean off dirty clothing before removing or changing it
(e.g. by vacuuming, although never use compressed air).
NOTICE:
Risk of system damage from incorrect or missing insulating rings.
Only use the insulating rings supplied.
For installation and connection:
Refer to the installation instructions of the relevant burner.
As standard, the thermal insulation in the burner door has an aperture of
270 mm for the blast tube. If the blast tube is larger than this, the
diameter of the aperture can be increased to a maximum of 360 mm.
If the hole in the thermal insulation of the burner door is increased, the
insulating rings supplied will no longer fit ( fig. 18, [4], page 22).
If the diameter of the blast tube is greater than 360 mm, speak to your
supplier. If the blast tube is not long enough to reach the inner edge of the
thermal insulation, a 45° chamfer can be applied to the thermal
insulation.
To mount the burner.
Refer to the installation instructions of the relevant burner.
Open the burner door ( chapter 6.9.1, page 20).
Push a gasket ( fig. 17, [1], page 22) onto the burner connector.
Fig. 17 Fitting the gasket
[1] gasket
Screw the burner to the burner plate ( fig. 18, [2], page 22).
Cut out insulating rings [4] in accordance with the diameter of blast
tube [5].
Fill the remaining gap on the inside of the burner door, between
burner door insulation [3] and blast tube [5], with adapted insulating
rings [4].
Fig. 18 Fitting the burner
[1] Burner
[2] Burner plate
[3] Thermal insulation for burner door
[4] Insulating rings
[5] Blast tube
Omit the installation of the insulating rings if this is stated in the
installation instructions from the burner manufacturer.
Close the burner door and tighten the hexagon bolts
( chapter 6.9.1, page 20).
0010014754-001
1
0010014747-001
1
2 3
5
4
270 mm
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Uni Condens 8000 F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Uni Condens 8000 F in the language / languages: English as an attachment in your email.

The manual is 10,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch Uni Condens 8000 F

Bosch Uni Condens 8000 F User Manual - English - 12 pages

Bosch Uni Condens 8000 F User Manual - German - 16 pages

Bosch Uni Condens 8000 F User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info