697430
20
Zoom out
Zoom in
Previous page
1/48
Next page
Installation
Uni Condens 8000 F – 6720867056 (2016/10)
20
The test pressure level is subject to the system components and to the
heating system. Observe country-specific regulations and standards.
Before commissioning, check the heating system for tightness to ensure
that no leaks will occur during operation.
Fill the heating system with water ( chapter 8.1, page 33 and
chapter 8.3, page 33).
Check all connections for leaks.
Pressure test the heating system.
Check flange connection and boiler connections for leaks.
Check the pipework for leaks.
After the tightness test, reinstate all components that were taken out
of operation.
Ensure that all pressure, control and safety equipment is functioning
correctly.
6.9 Opening and reversing the burner door
WARNING:
Risk of injury through falling burner door.
Never undo all 4 screws on the burner door.
Retighten the nuts that secure the burner door 2 weeks after
commissioning.
The burner door can be moved from the right-hand side (factory-set) to
the left-hand side.
The following instructions assume the factory-set pivoting direction.
6.9.1 Opening and closing the burner door
Opening the burner door
Undo 4 screws on the burner door.
Pivot the burner door open.
Fig. 13 Opening the burner door
Closing the burner door
Close the burner door.
The complete gasket must be pressed centrally onto the middle of the
combustion chamber. You can check whether the installation has been
performed correctly by carrying out a tightness test (e.g. chalk).
Fit the 4 screws in the burner door with washers.
Tighten the screws diagonally with a torque of 40 Nm.
6.9.2 Refitting the door hinges
WARNING:
Risk of injury from falling parts.
While the door hinges are being refitted, there is a risk of the burner door
falling.
Refit the door hinges before mounting the burner.
Ensure that the burner door is closed and secured with the four
screws.
As standard, the burner door pivots open from left to right. The following
instructions assume the standard pivoting direction.
If required due to space restrictions, the burner door can be converted
to open to the left.
Before starting work:
Open the burner door ( chapter 6.9.1, page 20).
When closing the burner door, insert the washer (can be found in the
pouch of the technical documents) between the burner door and the
lower l.h. door stay.
Ensure that the hole for the hinge pin is in line with the hole in the
washer.
Close the burner door.
Fit the four screws in the burner door.
Tighten the compression spring with the Allen screw until the rocker
arm to the hinge pin has some play ( fig. 14, page 20).
Remove retaining split pin [2] from hinge pin [1].
Fig. 14 Removing the retaining split pin
[1] Hinge pin
[2] Retaining split pin
Pull the hinge pin ( fig. 14, [1]page 20) upwards out of the hinge.
Unhook the rocker arm ( fig. 15, [3], page 21).
Release the compression spring [1] with Allen screw [4].
Remove the compression spring.
Fit the compression spring on the l.h. side.
Fit the washer [2].
Fit the Allen screw.
Pre-tighten the Allen screw until the washer has a clearance of 60 mm
towards the boiler front panel.
Hook in the rocker arm.
0010014740-001
0010014760-001
1
2
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Uni Condens 8000 F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Uni Condens 8000 F in the language / languages: English as an attachment in your email.

The manual is 10,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch Uni Condens 8000 F

Bosch Uni Condens 8000 F User Manual - English - 12 pages

Bosch Uni Condens 8000 F User Manual - German - 16 pages

Bosch Uni Condens 8000 F User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info