780636
14
Zoom out
Zoom in
Previous page
1/24
Next page
Rego 1000 – 6 721 831 662 (2021/03) en
14
Alarm
The information log displays information from the heat pump. The
control panel output mode displays the symbol for information log when
the active information is available.
13.2 Delete information log
The information log is deleted here.
13.3 Alarm log
The alarm log shows the alarms and warnings that have occurred. Alarm
category ( Chapter 7.5) is displayed in the top left corner of the
display. If the alarm is active, the alarm symbol (Chapter 4.3) is
displayed both in the alarm log and the initial menu of the control panel.
13.4 Delete alarm log
The alarm log is deleted here.
13.7 Alarm indication
Settings for alarm buzzer and status lamp are made here.
13.7.1 Alarm buzzer signal
13.7.1.1 Interval
Set the length of the alarm interval.
The alarm buzzer sounds for one second and is silent during the rest
of the interval. The setting applies to all alarm buzzers.
13.7.1.2 Blocking time
Set the times between which alarms buzzers should not be allowed to
produce an acoustic signal.
13.7.2 Alarm indication control unit
13.7.2.1 Block alarm buzzer
The setting applies only to the control unit's alarm buzzer.
13.7.3 Alarm indication room sensor
13.7.3.2 Block alarm indicator lamp
The setting applies to all room sensors.
6.10 Access level
Access level is Customer as standard: This level gives you access to all
functions that the user requires. The installer also has access to the
additional functions required at installation.
6.11 Return to factory settings
Select 15 Return to factory settings and Yes to reset all customer
settings to the factory settings. Settings made by the installer are not
affected.
7Alarm
7.1 Control unit and room sensor alarm lamp
The status lamp on the control unit is used to show ON/OFF status for the
heat pump but also to show possible alarms. The status lamp is therefore
also called alarm lamp.
In the event of an alarm the alarm lamp flashes red (control unit) until the
warning cause has disappeared. The alarm lamp is not used for warning
alarms.
The room sensor alarm lamp can be blocked.
The room sensor display is used to indicate alarms for some alarm
categories (10). The display window slowly flashes red until the
alarm has been acknowledged in the heat pump control unit, or been
automatically reset.
The room sensor alarm display function is referred to as alarm lamp in
this chapter.
The room sensor alarm lamp can be blocked.
7.2 Alarm buzzer at alarm
At an alarm the alarm buzzer on the heat pump sounds for one second
per alarm buzzer interval set. At certain times of the day the alarm buzzer
can be blocked or blocked altogether.
In the event of a warning, the alarm buzzer does not sound.
7.3 Acknowledgement of alarms
Acknowledgement means that you have to press to make the
alarm window disappear. What happens after acknowledgement is
described in the respective alarm description.
In most cases, warnings do not have to be acknowledged. The alarm
window disappears by itself once the warning cause has disappeared. It
is, however, possible to acknowledge the warning.
7.4 Alarm timer, alarm mode
In the event of an alarm that stops the compressor the control unit starts
a timer at 1h. If the fault does not recur additional heat may start when
the timer has counted down.
Behaviour Function
The lamp lights green
continuously.
The heat pump is running.
The lamp flashes red. There is an alarm which has not been
acknowledged.
The lamp lights red
continuously.
The alarm has been acknowledged but the
alarm cause remains.
The lamp flashes green
slowly.
The heat pump is in stand-by mode1).
1) Stand-by means that the heat pump is running but no heating or hot water
demand exists.
Table 9 Alarm lamp control unit
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Rego 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Rego 1000 in the language / languages: English as an attachment in your email.

The manual is 4.13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info