389182
25
Zoom out
Zoom in
Previous page
1/148
Next page
English | 25
Bosch Power Tools 2 609 005 110 | (23.11.10)
Screwdriver Tools
When working with screwdriver bits 24, a uni-
versal bit holder 23 should always be used. Use
only screwdriver bits that fit the screw head.
For driving screws, always position the “Drill-
ing/Impact Drilling” selector switch 4 to the
“Drilling” symbol.
Replacing the Drill Chuck
(PSB 750 RCE/PSB 750 RCA)
Removing the Drill Chuck (see figure J)
Clamp the short end of an Allen key 26 into the
keyless chuck 2.
Place the machine on a stable surface, e. g. a
workbench. Hold the machine firmly and loosen
the keyless chuck 2 by turning the Allen key 26
in rotation direction n. Loosen a tight seated
keyless chuck by giving the long end of the Allen
key 26 a light blow. Remove the Allen key from
the keyless chuck and completely unscrew the
keyless chuck.
Mounting the Drill Chuck (see figure K)
The keyless chuck is mounted in reverse order.
The drill chuck must be tightened with a
tightening torque of approx. 2535 Nm.
Replacing the Drill Chuck (PSB 650 RE/
PSB 6500 RE/PSB 650 RA)
Removing the Drill Chuck (see figure L)
Clamp the short end of an Allen key 26 into the
keyless chuck 2.
Place the machine on a firm surface, e. g. a
workbench. Hold the machine firmly, press the
spindle lock button 25 and loosen the keyless
chuck 2 by turning the Allen key 26 in rotation
direction n. Loosen a tight keyless chuck by giv-
ing the long end of the Allen key 26 a light blow.
Remove the Allen key from the keyless chuck
and completely unscrew the keyless chuck.
Mounting the Drill Chuck (see figure M)
The keyless chuck is mounted in reverse order.
The drill chuck must be tightened with a
tightening torque of approx. 2535 Nm.
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Reversing the Rotational Direction
(see figures NO)
The rotational direction switch 7 is used to re-
verse the rotational direction of the machine.
However, this is not possible with the On/Off
switch 8 actuated.
Right Rotation: For drilling and driving in
screws, push the rotational direction switch 7
left to the stop.
Left Rotation: For loosening and unscrewing
screws and nuts, press the rotational direction
switch 7 through to the right stop.
Setting the Operating Mode
Drilling and Screwdriving
Set the selector switch 4 to the “Drill-
ing” symbol.
Impact Drilling
Set the selector switch 4 to the “Im-
pact drilling” symbol.
The selector switch 4 engages noticeably and
can also be actuated with the machine running.
Switching On and Off
To start the machine, press the On/Off switch 8
and keep it pressed.
To lock the pressed On/Off switch 8, press the
lock-on button 6.
To switch off the machine, release the On/Off
switch 8 or when it is locked with the lock-on
button 6, briefly press the On/Off switch 8 and
then release it.
OBJ_BUCH-911-003.book Page 25 Tuesday, November 23, 2010 3:18 PM
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch psb 750 rca at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch psb 750 rca in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info