23203
16
Zoom out
Zoom in
Previous page
1/99
Next page
English - 4
Speed Table
The values shown in the chart are standard val-
ues. The necessary speed depends on the mate-
rial and the operating conditions, and can be de-
termined by practical testing.
Constant Electronic Control
(POF 1300 ACE)
Constant electronic control holds the speed con-
stant at no-load and under load, and ensures uni-
form working performance.
Depending on the cutting operation, the depth-of-
cut can be preset in several steps.
The adjustment of the depth-of-cut may
only be carried out when the router is
switched off.
Coarse Adjustment of the Depth-of-cut
Place the router on the workpiece to be ma-
chined.
POF 1300 ACE: Set the fine adjustment for
depth-of-cut in the center position with fine-ad-
justment knob 1; to do this, turn the fine-adjust-
ment knob until the markings 24 on the backside
of the router are in alignment, as shown.
Afterwards turn scale 2 to “0” (see figure ).
Set step buffer 11 to the lowest position; the
buffer snaps-in noticeably.
POF 1100 AE: Set the screws for the step
buffer 21 halfway in or out.
Set step buffer 11 to the lowest position; the
buffer snaps-in noticeably. When fine adjustment
of the depth-of-cut is desired, select one of the
3 steps that is fitted with the screw 21.
POF 1100 AE/POF 1300 ACE:
Loosen locking screw 8, so that depth stop 6
can be moved freely.
Release the clamping lever 3 by turning in
clockwise direction and slowly lower the router
until the router bit touches the surface of the
workpiece. Lock the router in position by turn-
ing the clamping lever 3 in anticlockwise direc-
tion.
Press depth stop 6 downwards until it touches
the stop buffer 11. Press down slider 7 and set
to “0”.
Adjust the depth stop 6 to the required routing
depth and tighten the wing screw 8. It is impor-
tant that the slider 7 is not adjusted afterwards.
Release the clamping lever 3 and guide the
router back up again.
The coarse adjustment of the depth-of-cut should
be checked by a trial cut and corrected, if neces-
sary.
Fine Adjustment of the Depth-of-cut
(POF 1300 ACE)
After a trial cut, fine adjustment can be carried out
by turning the fine adjustment knob 1 (1 scale
mark = 0.1 mm/1 rotation = 2.0 mm). The max-
imum adjustment is approx. +/– 8 mm.
Example: Slide router upwards again and meas-
ure the depth-of-cut (set value = 10.0 mm; actual
value = 9.8 mm).
Lift up router and underlay guide plate 13 in
such a manner that the router can plunge
freely without the router bit touching the work-
piece.
Lower the router again until the depth stop 6
touches the step buffer 11.
Afterwards set scale 2 to “0”.
Loosen wing screw 8.
With the fine adjustment 1, advance the depth-
of-cut in clockwise direction by 0.2 mm/
2 scale marks (= difference between required
value and actual value).
Retighten wing screw 8 again.
Slide router upwards again and check depth-
of-cut by carrying out another trial cut.
After setting the depth-of-cut, the position of the
index mark 7 on the depth stop should not be
changed anymore so that the currently adjusted
setting can always be read off of scale 5.
Material Router bit-Ø Speed stages
Hardwood 4 10 mm 5–6
(Beech) 12 20 mm 3–4
22 40 mm 1–2
Softwood 4 10 mm 5–6
(Pine) 12 20 mm 3–6
22 40 mm 1–3
Particle board 4 10 mm 3–6
12 20 mm 2–4
22 40 mm 1–3
Plastic 4 15 mm 2–3
16 40 mm 1–2
Aluminium 4 15 mm 1–2
16 40 mm 1
Setting the Depth-of-cut
C
1 609 929 F23 - Buch Seite 4 Montag, 19. April 2004 8:27 08
16 • 1 609 929 F23 • 04.04
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch POF1300ACE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch POF1300ACE in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 4,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch POF1300ACE

Bosch POF1300ACE User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 99 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info