23203
15
Zoom out
Zoom in
Previous page
1/99
Next page
English - 3
Inserting Router Bits (see figure )
Before any work on the machine itself, pull the
mains plug.
It is recommended to wear protective gloves
when inserting or replacing router bits.
Fold down chip shield 15.
Press spindle lock button 18 and keep de-
pressed. If required, turn the spindle by hand until
the lock engages.
Press the spindle lock button only when at a
standstill.
Insert router bit. The shank of the router bit must
be inserted at least 20 mm (shank length).
Tighten the tightening nut 17 with the open-end
spanner 25 (size 19 mm). Release the spindle
lock button 18.
Fold up chip shield 15.
Do not tighten the tightening nut of the
collet without a router bit inserted.
The dust that is produced while working can be
detrimental to health, inflammable or explo-
sive. Suitable safety measures are required.
Examples: Some dusts are regarded as carci-
nogenic. Use suitable dust/chip extraction and
wear a dust respirator.
Dust from light alloys can burn or explode. Al-
ways keep the workplace clean, as blends of
materials are particularly dangerous.
Mounting the Extraction Adapter
(see figure )
Press the chip shield 15 together at the holding
fixture on the base plate and remove it.
Fasten dust-collection adapter 27 to base
plate 12 with both knurled screws 26 and connect
vac via suction hose 28 (accessory).
When mounting the extraction adapter,
ensure correct mounting position!
For dust extraction, the 35-mm-Ø vacuum
hose 28 can be connected directly to the extrac-
tion adapter.
Clean the extraction adapter 27 regularly to en-
sure optimum dust extraction at all times.
The machine can be plugged directly into the re-
ceptacle of a Bosch all-purpose vacuum cleaner
with remote starting control. The vacuum cleaner
starts automatically when the machine is
switched on.
The vacuum cleaner must be suitable for the ma-
terial to be worked.
When vacuuming dry dust that is especially detri-
mental to health or carcinogenic, use a special
vacuum cleaner.
Observe correct mains voltage: The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Equipment marked with 230 V can also be con-
nected to 220 V.
Switching On and Off
For starting operation of the machine, actuate
the lock-off button 20 first, and then press and
hold the On/Off switch 23 afterwards.
POF 1300 ACE: A lamp lights out the routing.
To switch off the machine, release the On/Off
switch 23.
POF 1300 ACE: The lamp slowly goes out.
Speed Preselection
The required speed can be preselected with the
thumbwheel 22 (also while running).
1 2 = low speed
3 4 = medium speed
5 6 = high speed
The required speed is dependent on the material
and can be determined by practical testing.
After longer periods of working at low speed, al-
low the machine to cool down by running it for ap-
prox. 3 minutes at maximum speed with no load.
Dust/Chip Extraction
A
B
Initial Operation
1 609 929 F23 - Buch Seite 3 Montag, 19. April 2004 8:27 08
15 • 1 609 929 F23 • 04.04
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch POF1300ACE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch POF1300ACE in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 4,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch POF1300ACE

Bosch POF1300ACE User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 99 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info