23203
18
Zoom out
Zoom in
Previous page
1/99
Next page
English - 6
Routing with Parallel Guide
(Accessory see figures + )
Slide the parallel guide 30 with the guide rods 31
into the base plate 12 and tighten at the required
measure with the wing bolts 16.
Guide the machine with uniform feed and side-
ward pressure on the parallel guide 30 along the
edge of the workpiece.
Routing Circular Arc Profiles
(see figures + )
Reverse the parallel guide 30 (facing surfaces
point upwards) and insert the guide rods into the
base plate 12. Fasten centring pin 32 to parallel
guide (through hole) with wing bolt 33.
Puncture centring pin into marked centre of the
circular arc and guide router with consistent feed
across the workpiece surface.
Routing with the Curve Buffer
(see figures + )
Slide the parallel guide 30 with the guide rods 31
into the base plate 12. Fasten the curve buffer 34
with the guide roller mounted to the parallel
guide 30.
Guide the machine along the workpiece edge
with light sideward pressure.
Routing with the Router Compass
(Accessory see figure )
Use the router compass/guide rail adapter 35
(accessory) for circular routing jobs.
Mount the router compass as shown in the figure.
Screw pointed centring screw 40 in thread. Insert
the point of the centring screw in the centre of the
circular arc to be milled and ensure that it en-
gages in the workpiece surface.
Coarse-adjust the required radius by positioning
the router compass, then tighten the locking
screws 37 and 38.
After loosening the locking screw 37, the router
compass can be reset with the fine adjustment
knob 39 (1 scale mark = 0.1 mm/1 rotation =
2.0 mm).
Lead the router over the workpiece, holding the
router with the right handle 19 and the additional
router compass handle 36.
Routing with Guide Rail
(Accessory see figure )
Working with the guide rail 42 is possible only
with use of the guide-rail adapter 35 (accessory).
Straight routing cuts are to be carried out with
help of the guide rail 42 (accessory).
For this, always use the base spacer 41 (acces-
sory) to compensate the height difference.
Mount the guide-rail adapter 35 with the guide
rods 31.
Place the guide rail on the workpiece and mount
with a suitable clamping device (e. g. screw
clamp).
Place the router with guide-rail adapter 35 on the
guide rail.
Before any work on the machine itself, pull
the mains plug.
For safe and proper working, always keep
the machine and the ventilation slots clean.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts orders,
please always include the 10-digit order number
given on the nameplate of the machine.
WARNING! Important instructions for con-
necting a new 3-pin plug to the 2-wire cable.
The wires in the cable are coloured according to
the following code:
Do not
connect the blue or brown wire to the
earth terminal of the plug.
Important: If for any reason the moulded plug is
removed from the cable of this machine, it must
be disposed of safely.
G H
I K
L
M
N
Maintenance and Cleaning
O
strain relief
live = brown
neutral = blue
To be fitted
by qualified
professional only
1 609 929 F23 - Buch Seite 6 Montag, 19. April 2004 8:27 08
18 • 1 609 929 F23 • 04.04
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch POF1300ACE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch POF1300ACE in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 4,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch POF1300ACE

Bosch POF1300ACE User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 99 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info