Manual Bosch POF 1200 AE (page 25 of 146) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

78174

Zoom out

Zoom in

1/146

English | 25

Bosch Power Tools 1 609 929 S76 | (21.7.09)

POF 1400 ACE: The lamp slowly goes out.

Note: For safety reasons, the On/Off switch 22

cannot be locked; it must remain pressed during

the entire operation.

Constant Electronic Control (POF 1400 ACE)

Constant electronic control holds the speed

constant at no-load and under load, and ensures

uniform working performance.

Adjusting the Depth-of-cut

(see figure D)

f The adjustment of the depth-of-cut may on-

ly be carried out when the router is

switched off.

For coarse adjustment of the depth-of-cut, pro-

ceed as follows:

– Place the machine with the router bit mount-

ed on the workpiece to be machined.

– POF 1400 ACE:

– Set the fine-adjustment path to the centre

position with the adjustment knob 18. For

this, turn the adjustment knob 18 until the

marks 19 match as shown in the figure. After-

wards, set the scale 17 to “0”.

– Set the step buffer 9 to the lowest position;

the step buffer engages noticeably.

– POF 1200 AE: Screw the adjusting screws

for the step buffer 24 halfway in or out.

– Loosen the wing bolt for the depth stop 11

so that the depth stop 13 can be moved free-

ly.

– Push the clamping lever for locking of routing

depth 16 in rotation direction n and and

slowly lower the plunge router until the rout-

er bit 21 touches the surface of the work-

piece. Let go of the clamping lever 16 again

to lock this plunging depth.

If required, push the clamping lever 16 in ro-

tation direction o to lock it in place.

– Push the depth stop 13 downward until it

rests on the step buffer 9. Set the slide with

the index mark 12 to the “0” position on the

scale for the depth-of-cut adjustment 14.

– Set the depth stop 13 to the required depth-

of-cut and tighten the wing bolt for the depth

stop 11. Pay attention not to misadjust the

slide with the index mark 12 again.

– Push the clamping lever 16 in rotation direc-

tion n and guide the router to the uppermost

position.

For deep cuts, it is recommended to carry out

several cuts, each with little material removal.

By using the step buffer 9, the cutting process

can be divided into several steps. For this, ad-

just the desired depth-of-cut with the lowest

step of the step buffer and select the higher

steps first for the initial cuts.

POF 1200 AE: The clearance of the steps can be

changed by screwing the adjusting screws 24

further in or out.

Fine Adjustment of the Depth-of-cut

(POF 1400 ACE)

After a trial cut, the depth-of-cut can be set ex-

actly to the desired measure by turning the ad-

justment knob 18; turn in clockwise direction to

increase the cutting depth and in anticlockwise

direction to decrease the cutting depth. The

scale 17 can be used for guidance. One full turn

corresponds with a setting range of 2.0 mm; a

graduation mark on the top edge of the scale 17

corresponds with a 0.1 mm change of the set-

ting range. The maximum setting range is

± 8mm.

Example: The desired depth-of-cut is to be

10.0 mm; the trial cut resulted in a cutting depth

of 9.6 mm.

– Lift up the router and place, e. g., a piece of

scrap wood under the guide plate 7 so that

the router bit 21 cannot touch the workpiece

when lowering it. Push clamping lever 16 in

rotation direction n and slowly lower the

plunge router until the depth stop 13 faces

against the step buffer 9.

OBJ_BUCH-323-003.book Page 25 Tuesday, July 21, 2009 12:51 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch POF 1200 AE in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch POF 1200 AE Manual

Product: