Manual Bosch POF 1200 AE (page 27 of 146) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

78174

Zoom out

Zoom in

1/146

English | 27

Bosch Power Tools 1 609 929 S76 | (21.7.09)

Routing with the Curve Guide

(see figures K – L)

Slide the parallel guide 31 with the guide rods

30 into the base plate 6 and tighten it as re-

quired with the wing bolts 4.

Fasten the curve guide 34 with the guide roller

mounted through the hole on the parallel guide

31.

Guide the power tool with light lateral pressure

alongside the workpiece edge.

Routing with the Router Compass

(see figure M)

The router compass/guide-rail adapter 35 can

be used for circular routing jobs. Mount the

router compass as shown in the figure.

Screw the centring screw 40 into the thread on

the router compass. Insert the point of the cen-

tring screw into the centre of the circular arc to

be routed, paying attention that point of the

screw engages into the workpiece surface.

Coarsely adjust the required radius by moving

the router compass and tighten the wing bolts

37 and 38.

The length can be fine adjusted with the fine-ad-

justment knob 39 after loosening the wing bolt

38. One revolution corresponds with a setting

range of 2.0 mm. One graduation mark on the

fine-adjustment knob 39 changes the setting

range by 0.1 mm.

Guide the switched on power tool over the

workpiece with the right handle 2 and the router

compass handle 36.

Routing with Guide Rail (see figure N)

Straight routing cuts can be carried out with

help of the guide rail 41.

The base spacer 42 must be mounted in order to

compensate the height difference.

Mount the router compass/guide-rail adapter 35

as shown in the figure.

Fasten the guide rail 41 to the workpiece with

suitable clamping devices, e. g. screw clamps.

Place the machine with the guide-rail adapter 35

mounted onto the guide rail.

Routing with Guide Bushing (see figures O – P)

The guide bushing 43 enables template and pat-

tern routing on workpieces.

Choose a suitable guide bushing, depending on

the thickness of the template or the pattern. Be-

cause of the projecting height of the guide bush-

ing, the template must have a minimum thick-

ness of 8 mm.

Actuate the release lever 20 and insert the guide

bushing 43 from below into the base plate 6. En-

sure that the encoding keys clearly engage in the

grooves of the guide bushing.

f Select a router bit with a diameter smaller

than the interior diameter of the guide

bushing.

For routing with the guide bushing

43 proceed

as follows:

– Guide the switched on power tool with the

guide bushing toward the template.

– Push clamping lever 16 down and slowly low-

er the plunge router until the adjusted depth-

of-cut is reached. Let go of the clamping le-

ver 16 again to lock this plunge depth.

If required, push clamping lever 16 up again

to finally lock it in place.

– Guide the switched on power tool with the

protruding guide bushing alongside the tem-

plate applying lateral pressure.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

f In extreme working conditions, conductive

dust can accumulate in the interior of the

machine when working with metal. The pro-

tective insulation of the machine can be de-

graded. The use of a stationary extraction

system is recommended in such cases as

well as frequently blowing out the ventila-

tion slots and installing a residual current

device (RCD).

OBJ_BUCH-323-003.book Page 27 Tuesday, July 21, 2009 12:51 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch POF 1200 AE in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch POF 1200 AE Manual

Product: