78174

Bosch POF 1200 AE Manual

24
Zoom out
Zoom in
Previous page
1/146
Next page
24 | English
1 609 929 S76 | (21.7.09) Bosch Power Tools
– Use dust extraction whenever possible.
– Provide for good ventilation of the work-
ing place.
– It is recommended to wear a P2 filter-
class respirator.
Observe the relevant regulations in your
country for the materials to be worked.
Mounting the Extraction Adapter
The extraction adapter 28 can be mounted with
the hose connection to the front or to the rear.
When mounting with the hose connection in
front, the chip shield 5 must be removed first.
Fasten the extraction adapter 28 with the two
knurled screws 29 to the base plate 6.
To ensure optimum extraction, the extraction
adapter 28 must be cleaned regularly.
Connecting the Dust Extraction
Insert an extraction hose (Ø 35 mm) 27 (acces-
sory) into the mounted extraction adapter. Con-
nect the extraction hose 27 to a vacuum cleaner
(accessory).
The machine can be plugged directly into the re-
ceptacle of a Bosch all-purpose vacuum cleaner
with remote starting control. The vacuum clean-
er starts automatically when the machine is
switched on.
The vacuum cleaner must be suitable for the ma-
terial being worked.
When vacuuming dry dust that is especially det-
rimental to health or carcinogenic, use a special
vacuum cleaner.
Mounting the Chip Shield (see figure C)
Insert the chip shield 5 from the front into the
guide in such a manner that it engages. To re-
move the chip shield, grasp it by the sides and
pull it off toward the front.
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Preselecting the Speed
The required speed can be preselected with the
thumbwheel 23 (also while running).
1 – 2 low speed
3 – 4 medium speed
5–6 high speed
The values shown in the chart are standard val-
ues. The necessary speed depends on the mate-
rial and the operating conditions, and can be de-
termined by practical testing.
Switching On and Off
Adjust the depth-of-cut before switching on or
off; see Section “Adjusting the Depth-of-cut”.
To start the machine, first push the lock-off but-
ton for the On/Off switch 1 and then press the
On/Off switch 22 and keep it pressed.
POF 1400 ACE: A lamp illuminates the routing
area.
To switch off the machine, release the On/Off
switch 22.
Material Router bit
diameter (mm)
Thumb-
wheel 23
Hardwood
(Beech)
4–10
12 – 20
22 – 40
5–6
3–4
1–2
Softwood (Pine) 4 – 10
12 – 20
22 – 40
5–6
3–6
1–3
Particle Board 4 – 10
12 – 20
22 – 40
3–6
2–4
1–3
Plastics 4 – 15
16 – 40
2–3
1–2
Aluminium 4 – 15
16 – 40
1–2
1
OBJ_BUCH-323-003.book Page 24 Tuesday, July 21, 2009 12:51 PM
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch POF 1200 AE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch POF 1200 AE in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info