Manual Bosch PMF 10,8 LI (page 24 of 152) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

460547

Zoom out

Zoom in

1/152

24 | English

2 609 004 157 | (11.5.10) Bosch Power Tools

Operation

Starting Operation

Inserting the Battery

f Use only original Bosch lithium ion batter-

ies with the voltage listed on the nameplate

of your power tool. Using other batteries can

lead to injuries and pose a fire hazard.

Note: Use of batteries not suitable for the ma-

chine can lead to malfunctions of or cause dam-

age to the power tool.

Insert the charged battery 2 into the handle until

it can be felt to engage and faces flush against

the handle.

Switching On and Off

To switch on the power tool, push the On/Off

switch 5 toward the front in the direction of the

“1” on the switch.

To switch off the power tool, push the On/Off

switch 5 toward the rear in the direction of the

“0” on the switch.

The lithium ion battery is protected against

deep discharging by the “Electronic Cell Protec-

tion (ECP)”. When the battery is empty, the ma-

chine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Note: If the machine should automatically

switch off because of a discharged or overheat-

ed battery, make sure to set the machine’s

On/Off switch 5 to off. Charge the battery and

allow it to cool down before restarting the ma-

chine. Otherwise the battery can become dam-

aged.

Preselecting the Orbital Stroke Rate

With the thumbwheel for preselection of the or-

bital stroke rate 3, you can preselect the required

orbital stroke rate, even during operation.

The required stroke rate depends on the materi-

al and the working conditions and can be deter-

mined through practical testing.

When sawing and cutting harder materials, e.g.,

wood or metal, it is recommended to work with

orbital stroke rate “5” or “E”; for softer materi-

als, such as plastic, orbital stroke rate “4” is rec-

ommended.

When sanding harder materials, e.g., wood or

metal, it is recommended to work with orbital

stroke rate “5”; for softer materials, such as soft-

wood, orbital stroke rate “4” is recommended.

The Eco electronics are active at the maximum

orbital stroke rate “E”: When the application

tool is not subject to load, the orbital stroke rate

is automatically reduced (after approx. 1 s). The

reduction extends the battery operating dura-

tion per charge, and the reduced vibrations en-

able precise applying of the application tool on-

to the workpiece. As soon as load is applied to

the application tool again, the machine automat-

ically accelerates to the maximum orbital stroke

rate.

The Eco electronics, however, are not suitable

for sanding activities. Instead, orbital stroke

rate “5”, which has the same oscillation rate as

setting “E” yet without the Eco electronics, is

suitable for sanding.

Working Advice

Note: Do not cover off the venting slots 6 of the

machine while working, as this reduces the

working life of the machine.

While working with HCS tools make sure that

the covering of the tools is undamaged.

Operating Principle

Due to the oscillating drive the application

tool/accessory swings up to 20000 times per

minute for 2.8°. This allows for precise work in

narrow spaces.

Work with low and uniform appli-

cation pressure, otherwise, the

working performance will decline

and the application tool can be-

come blocked.

While working, move the machine

back and forth, so that the appli-

cation tool does not heat up ex-

cessively and become blocked.

OBJ_BUCH-1170-002.book Page 24 Tuesday, May 11, 2010 3:36 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PMF 10,8 LI in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PMF 10,8 LI Manual

Product: