460547
21
Zoom out
Zoom in
Previous page
1/152
Next page
English | 21
Bosch Power Tools 2 609 004 157 | (11.5.10)
Assembly
Battery Charging
f Use only the battery chargers listed on the
accessories page. Only these battery charg-
ers are matched to the lithium ion battery of
your power tool.
Note: The battery is supplied partially charged.
To ensure full capacity of the battery, complete-
ly charge the battery in the battery charger be-
fore using your power tool for the first time.
The lithium ion battery can be charged at any
time without reducing its service life. Interrupt-
ing the charging procedure does not damage the
battery.
The battery is equipped with a NTC temperature
control which allows charging only within a tem-
perature range of between 0 °C and 45 °C. A long
battery service life is achieved in this manner.
Removing the Battery
To remove the battery 2, press the unlocking
buttons 1 and pull the battery out of the ma-
chine to the rear. Do not exert any force.
Battery Charge-control Indication
When the power tool is switched on, the battery
charge-control indicator 4 signals the still avail-
able battery capacity or an overload.
When the battery charge-control indicator 4
flashes red, the machine is subject to overload.
Please observe the information in section “Tem-
perature-dependent Overload Protection”,
page 25.
Changing the Tool
f Before any work on the machine itself (e.g.
maintenance, tool change, etc.) as well as
during transport and storage, remove the
battery from the power tool. There is danger
of injury when unintentionally actuating the
On/Off switch.
f Wear protective gloves when changing ap-
plication tools/accessories. Contact with
the application tool/accessoriy can lead to
injuries.
Selecting the Application Tool/Accessory
The following table shows examples for application tools. Further application tools can be found in
the extensive Bosch accessories program.
Indication Capacity
Continuous lighting, green >70 %
Continuous lighting, yellow 3070 %
Continuous lighting, red <30 %
Accessory Material Application
BIM segment
saw blade
Wooden materials,
plastic, non-ferrous
metals
Separating and plunge cuts; also for sawing
close to edges, in corners and hard to reach
areas;
Example: shortening already installed bottom
rails or door hinges, plunge cuts for adjusting
floor panels
Base plate for
sanding, se-
ries Delta
93 mm
Depends on sand-
ing sheet
Sanding surfaces close to edges, in corners
or hard to reach areas;
Depending on the sanding sheet for, e.g.,
sanding wood, paint, varnish, stone
HCS plunge
cut saw blade,
wood
Wooden materials,
soft plastics
Separating and deep plunge cuts; also for
sawing close to edges, in corners and hard to
reach areas;
Example: narrow plunge cut in solid wood for
installing a ventilation grid
OBJ_BUCH-1170-002.book Page 21 Tuesday, May 11, 2010 3:36 PM
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PMF 10,8 LI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PMF 10,8 LI in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info