766889
23
Zoom out
Zoom in
Previous page
1/303
Next page
English | 23
Remove the suction tube(13) with the container
seal(17) and rinse it thoroughly.
Reattach the suction tube(13) with the container
seal(17) to the spray gun.
Fill the container(7) with warm water and fit it to the
spray gun(1)again.
Connect the air hose(20) to the spray gun(1)again.
Spray until only clear water comes out. You may have to
fill the container with warm water again.
Remove the air hose(20) from both the base unit(22)
and the spray gun(1).
Clean the base unit if necessary with a moistened cloth
and then remove the base unit(22) and the air hose(20)
from the immediate cleaning environment.
Remove the cap nut(3), the air cap(2), the gasket(12),
the nozzle cap used(10)/(9) with the O-ring(11) and the
suction tube(13) with the container seal(17).
When doing so, ensure that the O-ring(11) remains on
the nozzle cap.
Clean all paint-carrying parts in a bucket with warm water
using a commercially available washing-up brush. Also
clean the paint channel(19) of the spray gun(1).
Check that the suction tube(13) and the container
seal(17) are free of spray material and undamaged.
If required, clean the container seal(17) again with warm
water.
Clean the ventilation hole (18) using a suitable object.
PFS2000: If required, clean the filling sieve(14) thor-
oughly with warm water.
Clean the outside of the container(7) and the spray
gun(1)with a damp cloth.
Allow all components to dry thoroughly before assem-
bling them.
Reassemble the fine-spray system in reverse order.
Slide the container seal(17) upwards again into the
groove of the suction tube(13).
Ensure that the container seal is positioned precisely all
around in the suction tube groove in order to seal the
spray gun correctly.
Make sure that you slide the suction tube(13) all the way
back onto the paint channel(19).
Cleaning After Using Solvent-Based Paints (see figureK)
Always clean the spray gun and the container for the spray
material with the respective diluting agent for the spray ma-
terial being used.
Never clean the nozzle and air holes in the spray gun with
pointed objects.
Wear suitable gloves during cleaning work involving solvents
and solvent-based paints.
Switch off the base unit(22) and remove the air
hose(20) from the spray gun(1).
Clean the base unit if necessary with a cloth moistened
with diluting agent and then remove the base unit(22)
and the air hose(20) from the immediate cleaning envir-
onment.
Remove the container(7) from the spray gun(1).
Hold the container(7) underneath the suction tube(13)
and pull the trigger switch(6) on the spray gun so that the
spray material can flow back into the container.
Empty the container(7).
The spray material can be stored in an airtight, sealed
paint container for other applications. Use the spare
container(8) with cover or the original spray material
container, for example, for this purpose.
Clean the container(7).
Remove the suction tube(13) with the container
seal(17) and rinse it thoroughly.
Reattach the suction tube(13) with the container
seal(17) to the spray gun.
Fill the container(7) halfway with solvent and fit it to the
spray gun(1)again.
Shake the spray gun several times.
Make sure that you do not spray the diluting agent. There
is a risk of explosion.
Remove the container(7) from the spray gun(1)and
empty it completely into a sealable material tin.
Remove the cap nut(3), the air cap(2), the gasket(12),
the nozzle cap used(10)/(9) with the O-ring(11) and the
suction tube(13) with the container seal(17).
When doing so, ensure that the O-ring(11) remains on
the nozzle cap.
Clean all paint-carrying parts in a bucket with diluting
agent using a commercially available washing-up brush.
Also clean the paint channel(19) of the spray gun(1).
Check that the suction tube(13) and the container
seal(17) are free of spray material and undamaged.
If required, clean the container seal(17) again with dilut-
ing agent.
Clean the ventilation hole (18) using a suitable object.
PFS2000: If required, clean the filling sieve(14) thor-
oughly with diluting agent.
Clean the outside of the container(7) and the spray
gun(1)with a cloth moistened in diluting agent.
Allow all components to dry thoroughly before assem-
bling them.
Reassemble the fine-spray system in reverse order.
Slide the container seal(17) upwards again into the
groove of the suction tube(13).
Ensure that the container seal is positioned precisely all
around in the suction tube groove in order to seal the
spray gun correctly.
Make sure that you slide the suction tube(13) all the way
back onto the paint channel(19).
Material Disposal
Contaminated diluting agent, remnants of spray material
and, if applicable, remnants of diluting agent must be dis-
posed of properly and in an environmentally friendly man-
ner. Observe the manufacturer's disposal information and
the local regulations for disposal of hazardous waste.
Bosch Power Tools 1 609 92A 687 | (16.09.2021)
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PFS 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PFS 2000 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 10,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info