766889
24
Zoom out
Zoom in
Previous page
1/303
Next page
24 | English
Chemicals harmful to the environment may not be disposed
of into soil, groundwater or bodies of water. Never pour
chemicals harmful to the environment into the sewerage sys-
tem.
Storage
Before putting the fine-spray system into storage, thor-
oughly clean the fine-spray system and allow all parts to
dry completely before assembling them.
If the fine-spray system is not being used, the elastic band
together with the pin on the base unit(22) serve as a prac-
tical storage option for the air hose(20).
Troubleshooting
Problem Cause Corrective measure
Spray material does not
cover properly Spraying capacity too low Turn thumbwheel (5) in the + direction
Clearance to target area too large Reduce spray distance
Not enough spray material on target area, too
few spray paths sprayed over target area Apply more spray paths over target area
Spray material too viscous Dilute the spray material again and carry out a
test-spray run
Spray material runs off after
coating Too much spray material applied Turn thumbwheel (5) in the direction
Clearance to target area too close Increase spray distance
Viscosity of spray material too low Add original spray material
Spray material applied too often over same
spot Remove spray material; reduce number of
spray paths over same spot
Atomisation too coarse Spraying capacity too high Turn thumbwheel (5) in the direction
PFS2000: White nozzle cap (10) fitted (nozzle
diameter too large)
Fit the grey nozzle cap (9)
Nozzle needle (16) contaminated Clean nozzle needle
Spray material too viscous Dilute the spray material again and carry out a
test-spray run
Air filter (29) heavily contaminated Change air filter
Excessive paint mist Too much spray material applied Turn thumbwheel (5) in the direction
Clearance to target area too large Reduce spray distance
Spray jet pulsates Not enough spray material in container Refill spray material
Ventilation hole (18) on suction tube (13)
clogged
Clean the suction tube and the ventilation hole
Suction tube (13) loose Slide the suction tube all the way onto the paint
channel (19)
Nozzle cap (10)/(9) loose Tighten the nozzle cap
Air filter (29) heavily contaminated Change air filter
Spray material too viscous Dilute the spray material again and carry out a
test-spray run
Spray material dripping at
the nozzle cap Deposit of spray material on the nozzle cap
(10)/(9), the nozzle needle (16) and the air
cap (2)
Clean the nozzle cap, nozzle needle and air cap
Nozzle cap (10)/(9) loose Tighten the nozzle cap
No spray material coming
out of the nozzle cap Suction tube (13) loose Slide the suction tube all the way onto the paint
channel (19)
Nozzle needle (16) clogged Clean nozzle needle
Suction tube (13) clogged Clean suction tube
Ventilation hole (18) on suction tube (13)
clogged
Clean the suction tube and the ventilation hole
1 609 92A 687 | (16.09.2021) Bosch Power Tools
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PFS 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PFS 2000 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 10,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info