Manual Bosch PFS 2000 (page 21 of 303) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian)

766889

Zoom out

Zoom in

1/303

English | 21

– Pour the spray material into the container(7) up to no

more than the 800 mark.

– Turn the suction tube(13) so that the spray material can

be sprayed with almost no residue:

For spray jobs on horizontal

surfaces/objects Towards the front in the dir-

ection of the nozzle/air cap

For spray jobs overhead Towards the rear in the dir-

ection of the handle

– Carry out a test-spray run on a test surface.

If the spray pattern is optimal, you can begin spraying.

If the spraying results are unsatisfactory or no paint is emit-

ted: (see "Troubleshooting", page24)

Starting Operation

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool.

uMake sure that the base unit cannot draw in dust or

other contamination during operation.

uMake sure never to spray on the base unit.

uStop spraying if fluid escapes from places other than

the intended nozzle during spraying, and restore the

spray gun to its proper condition. There is a risk of elec-

tric shock.

uDo not direct the fine-spray system against yourself,

other persons or animals.

Switching on (seefigureE)

–PFS2000: Check whether the correct nozzle cap is fit-

ted. (see "Changing the nozzle cap (PFS2000)

(seefigureC)", page20)

– Plug the mains plug into a plug socket.

– Grasp the spray gun by the handle and point it at the tar-

get area.

– Slide the on/off switch(23) forwards.

– Pull the trigger switch(6) on the spray gun.

Note: Air always flows out at the air cap(2) when the base

unit is switched on.

Switching Off

– Let go of the trigger switch(6) and slide the on/off

switch(23) backwards.

– Pull the mains plug from the plug socket.

Working Advice

Spraying (seefigureF)

Note: Pay attention to the wind direction when you are using

the power tool outdoors.

– Firstly, carry out a spray test and adjust the spray pattern

and the spray material volume according to the spray ma-

terial.

For adjustments, see the following sections.

– Make sure to hold the spray gun with a uniform clearance

of 20–25cm vertical to the object being sprayed.

– Begin the spraying procedure outside the target area.

– Move the spray gun evenly horizontally or vertically ac-

cording to the spray pattern configuration.

An even surface quality can be achieved when the spray

paths overlap by 4–5cm.

– When spraying horizontal objects or spraying overhead,

hold the spray gun at a slight angle and move back from

the sprayed surface.

Risk of tripping! Be aware of potential obstacles.

– Avoid interruptions when spraying the target area.

Guiding the spray gun evenly will provide uniform surface

quality.

A non-uniform spraying angle and distance will lead to heavy

formation of paint mist and consequently an uneven surface.

– End the spraying procedure outside the target area.

Never completely empty the container for the spray material

by spraying. If the suction tube is no longer immersed in the

spray material, the spray jet will be interrupted and this will

result in an inconsistent surface.

– After breaks or refilling the container(7), check the

nozzle cap(10)/(9) and the air cap(2) and clean them if

required.

– If the spray material settles on the air cap(2) or the

nozzle cap, clean the components with a suitable brush or

a damp cloth.

Adjusting the spray pattern

uNever actuate the trigger switch(6) while adjusting

the air cap(2).

– Turn the air cap(2) to the required position.

Air cap Spray jet pattern Application

Horizontal flat jet

for vertical working

direction

Bosch Power Tools 1 609 92A 687 | (16.09.2021)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PFS 2000 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 10,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PFS 2000 Manual

Product: