Manual Bosch pbh 2900 fre (page 25 of 158) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

388876

Zoom out

Zoom in

1/158

English | 25

Bosch Power Tools 1 609 929 T39 | (19.11.10)

Changing the Tool

The dust protection cap 4 largely prevents the

entry of drilling dust into the tool holder during

operation. When inserting the tool, take care

that the dust protection cap 4 is not damaged.

f A damaged dust protection cap should be

changed immediately. We recommend hav-

ing this carried out by an after-sales serv-

ice.

Inserting SDS-plus Drilling Tools

(see figure G)

The SDS-plus drill chuck allows for simple and

convenient changing of drilling tools without the

use of additional tools.

– PBH 3000-2 FRE: Insert the SDS-plus quick

change chuck 2.

– Clean and lightly grease the shank end of the

tool.

– Insert the tool in a twisting manner into the

tool holder until it latches itself.

– Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus

drilling tool can move freely. This causes a cer-

tain radial run-out at no-load, which has no ef-

fect on the accuracy of the drill hole, as the drill

bit centres itself upon drilling.

Removing SDS-plus Drilling Tools

(see figure H)

– Push back the locking sleeve 5 and remove

the tool.

Inserting Drilling Tools without SDS-plus into

the Key Type Drill Chuck (PBH 2800 RE)

Note: Do not use tools without SDS-plus for

hammer drilling or chiselling! Tools without

SDS-plus and their drill chucks are damaged by

hammer drilling or chiselling.

– Insert the key type drill chuck 21.

– Open the key type drill chuck 21 by turning

until the tool can be inserted. Insert the tool.

– Insert the chuck key into the corresponding

holes of the key type drill chuck 21 and clamp

the tool uniformly.

– Turn the mode selector switch 12 to the

“drilling” position.

Removing Drilling Tools without SDS-plus from

the Key Type Drill Chuck (PBH 2800 RE)

– Turn the sleeve of the key type drill chuck 21

with the drill chuck key in anticlockwise di-

rection until the drilling tool can be removed.

Inserting Drilling Tools without SDS-plus into

the Keyless Chuck

(PBH 2900 FRE/PBH 3000 FRE Set/

PBH 3000-2 FRE) (see figure I)

Note: Do not use tools without SDS-plus for

hammer drilling or chiselling! Tools without

SDS-plus and their drill chucks are damaged by

hammer drilling or chiselling.

– PBH 2900 FRE/PBH 3000 FRE Set: Insert the

keyless chuck 23.

– PBH 3000-2 FRE: Insert the quick change

keyless chuck 1.

– Hold the rear sleeve 26 of the keyless chuck

23 and turn the front sleeve 25 in anticlock-

wise direction until until the tool can be in-

serted. Insert the tool.

– Tightly hold the rear sleeve of the keyless

chuck 23 and firmly turn the front sleeve

clockwise by hand until the locking action is

no longer heard. This automatically locks the

drill chuck.

– Check the tight seating by pulling the tool.

Note: If the tool holder was opened to the stop,

then a latching noise possibly may be heard

while closing the tool holder and the tool holder

will not close.

In this case, turn the front sleeve 25 once in an-

ticlockwise direction. Afterwards, the tool hold-

er can be closed (tightened).

– Turn the mode selector switch 12 to the

“drilling” position.

Removing Drilling Tools without SDS-plus from

the Keyless Chuck

(PBH 2900 FRE/PBH 3000 FRE Set/

PBH 3000-2 FRE) (see figure J)

– Firmly hold the rear sleeve 26 of the keyless

chuck and turn the front sleeve 25 of the key-

less chuck in anticlockwise direction until

the drilling tool can be removed.

OBJ_BUCH-318-003.book Page 25 Friday, November 19, 2010 4:36 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch pbh 2900 fre in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch pbh 2900 fre Manual

Product: