697319

Bosch MC 400 Manual

16
Zoom out
Zoom in
Previous page
1/88
Next page
16 | Mounting
MC 4006 720 816 739 (2015/05)
3.2.4 Overview of the terminal assignment
This overview indicates which system parts can be connected for all
terminals in the module. The components identified with * (such as HS1
and M1) in the system are possible alternatives. Depending on the
module's use, one of the components is connected to the “BUS1”
terminal.
More complex systems can be created in combination with additional
cascade modules. Terminal assignments, which deviate from the
terminal overview, are therefore possible.
Key to the Fig. above and to Fig. 23 to 25 (no terminal designation):
230 V AC Mains voltage connection
A0 Remote fault indicator
BUS EMS 2 / EMS plus BUS system (do not connect to
BUS1 ... ...BUS4)
BUS1...4 EMS / EMS plus BUS system or EMS 2 / 2-wire BUS
(connect directly to HS1 ... HS4 or M1 ...M4)
CON User interface with EMS 2 / EMS plus BUS system
(Controller)
GLT Building management system with 0-10 V interfaces
(Building Management System)
HS1, HS5, HS9, HS13
Heat source 1 (HS1 to BUS1), 2 (HS5 to BUS2),
3 (HS9 to BUS3) and 4 (HS13 to BUS4) to single MC 400 /
(Heat Source)
HS1...4 Heat source 1 (to BUS1) ... 4 (to BUS4) to first subordinate
MC 400 (M1) / (Heat Source)
HS5...8 Heat source 1 (to BUS1) ... 4 (to BUS4) to second
subordinate MC 400 (M2) / (Heat Source)
I2 Switch for maximum output (all devices are switched to
maximum output when closed; Input)
I3 Stop switch (heat requirement for all devices is interrupted
when open; Input)
IA1 230 V controller (input)
M1...4 subordinate cascade module 1 (to BUS1) ... 4 (to BUS4)
MC 400 Cascade module
MM 100 Heating circuit module (EMS 2 / EMS plus)
PC0 Cascade pump (On/off or optional speed control via 0-10 V
signal with connection OC1; Cascade Pump); only with heat
sources without a pump
PC1 Heating pump (Pump Circuit); feed pump or heating pump
for one heating circuit without mixer and without MM 100
P0 Input and feedback for output control via a 0-10 V signal
(power input and output); Terminal assignment: 1 – earth;
2 – output; 3 – input (optional)
T0 Flow temperature sensor (Temperature sensor)
T1 Outside temperature sensor (T
emperature sensor)
T2 Return temperature sensor (only required when PC0 with
speed control via 0-10 V signal is at connection OC1;
otherwise optional; Temperature sensor)
1) Only required, if no stop switch is connected to terminal I3.
If no stop switch (N/C contact) is connected to terminal I3:
▶ Connect the jumper, which is included in the scope of
delivery, to terminal I3.
6 720 809 449-16.3O
HS1*
M1*
HS5*
M2*
HS9*
M3*
HS13*
M4*
CONT2IA1A0
PC0
123
P0
0-10V
123
0-10V
M
PC1
NL
T1 T0
M
PC0
NL
I2 I3230 V AC230 V AC
CNO NC
A0
120/230 V AC
NL N LINN63L
120/230VAC 120/230VAC
PC1 IA1
123
0-10V
1212
T1
T2 BUS1
MC400
120/230 V AC
≤ 24V
0
1
2
3
4
5
6
7
8
9
10
10
1)
12 12
BUS
12
BUS2
123
OC1
BUS3 BUS4
12 1212 1212
T0 I2 I3
≤ 24V
N63
PC0
1)
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch MC 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch MC 400 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info